aleph objects 3d models

This is a copy of Aleph Objects Z-ends sized up for 10mm rods, instead of the stock 8mm rods on the MendelMax. ... Instructions If you use these and like them tell the guys at Aleph Objects thank you for another great object.

The original clamp (http://www.thingiverse.com/thing:13228) held the M8 nut too tightly (probably due to poor print quality) and this created binding that my stepper motor could not overcome. This modification does not hold the nut as tightly and can...

Wanting to move away from the cast x-ends but also liking the clamp style, we designed some new ones to work with the boltable PLA bushings. These are interchangeable with the standard Prusa or cast Clonedel x-ends. This x-end set calls for a little...

NOTE 1/31/2012: We've updated the design by making the clamps a bit tighter. We found that the smooth rod grooves had a very tight tolerance and would not clamp the rods tight enough in some cases. This is a small update to the AO X-ends. The only...

New version uploaded, older versions removed. The new version has the corrected ID, so it should need almost zero sanding to fit your LM8UUs. It also has enough room for washers and the head of your bolt. ... ...

These X-ends work the same way as the original AO X-ends but are compatible with 3/8 inch ACME lead screw thread and nuts. The parts we used are McMaster Carr parts: -3/8" 12 Brass ACME nut: #95155A111 -3/8" 12 plain steel ACME rod 36": #98935A817...

I designed this thing, to take advantage of the endstop flag holders on the Aleph Objects Z Motor Mounts without having to mount the endstop on the X-End. Ultimately, it's more complicated than necessary and I should have just used a standard...

In the process of building another prusa and wanting to use my known good parts with improvements including LM8UU bearings I adapted thing 21324 to mount on the AO X ends (http://www.thingiverse.com/thing:15492). ...Use...

LM8UU now works on AO Motor X end. Post-printing, the corner of the bracket is trimmed about 0.5MM to prevent interference with the motor. Xacto is your friend. Instructions Print, Clear off clamp...

SCAD included, as your inner dimension gap may be different than mine. ... Instructions Use #3 screws/nuts

derived from http://www.thingiverse.com/thing:22129, corrected front to back hole spacing, was off about 10mm.. ... Instructions i used .2-.3mm layer / .6-.8 density

The original was like 10mm too small width wise, the bearing also was pretty tight, but i'm gonna print it at a higher density / finer layer and see what happens, Instructions .2-.3mm layer, 40-80%...

Aleph Candle Holder

Aleph is the first letter in the Hebrew alphabet. This aleph looks like it's being carved in stone. Designed in ZBrush. Update 1: This thing is now available to order from Shapeways at http://shpws.me/nJtz in a wide variety of materials. Update...

avec son petit frère qui fait 2 cm. pour le grand je l'ai coupé avec netfabb en 2 partie, puis coller ensemble avec un peu d'acétone. ...pour une couleur rouge intense je l'ai peint à l'aérographe avec une couleur rouge intense pour un meilleur effet.

First letter int the hebrew alphabet

No description provided.

... Weeks! If you find errors or i forgot a Unitname, please feel free to PM me! I will edit it as soon as possible! Check out my Samples, with them you can test the Quality and your Printer! https://cults3d.com/en/3d-model/game/firearc-aleph-samples

... I then copied those studs to a new object, scaled them up a bit, and used the result to cut corresponding holes into the base, with a nominal 0.15mm gap around all sides. Finally, I created custom support objects for the Aleph's upper Yod segment.

simple objects

simple objects

This is just a downloadable Testmodel for you to check the design and the printablility of my FireArcs for Infinitys Aleph Faction. Every Basesize is included. ... If you are interested in my Arcs, here you can check them out.

Unfortunately, these art objects are very expensive and very few can afford them. Here you can download original works of art from the sculptor Eberhard Fiebig as a 3D file and print them out yourself. These special "rotated" works of art are one of...

Aleph Style Infinity Base set with directional facing arrows and magnetic slots Includes:15x25mm7x40mm5x55mm All bases are slotted for 6x2mm magnets. ... Files only, no physical objects included

Shelf brackets to hold an Aleph One LED Light strip made by Entek Allows the strip to be mounted on the edge or depending on how deep your shelf is mounted front to back as in the photo

Aleph OS-5802-2 Opto Sensor http://www.aleph-eu.com/product/p/OS-5802-2

28mm Feuerbach for Aleph from Infinity: The Game Designed for SLA or LCD printing. ...I doubt it'll work on FDM at this scale.

28mm SMG for O12/Aleph from Infinity: The Game Designed for SLA or LCD printing. ...I doubt it'll work on FDM at this scale.

28mm HMG for O12/Aleph from Infinity: The Game Designed for SLA or LCD printing. ...I doubt it'll work on FDM at this scale.

No description provided.