alexmos 32 bit case 3d models

Case for Heltec LoRa 32 radio. Designed to fit 1100 mAh battery. ...Uses three m2.5x20mm screws.

A case for Vectrom 32 - multicart for Vectrex. ... This is a case for a PCB sold by retroHax.de ( https://www.ebay.fr/str/retrohaxde)

This is the case for esp 32 WROOM 32D microcontroller - ESP 32 DevkitC V4. ...I personally printed it at 0.2mm layer height but I recommend to print it at 0.12mm layer height.

For the ESP 32 Cam Case a Lampbracket. Bracket can screwed on the upper or on the horizontal part. Case: https://www.prusaprinters.org/prints/30066-esp-32-cam-case Lamp:...

I modeled a straightforward case in Fusion 360 to accommodate a HiLetGo Wifi 32 with OLED Screen. This project is part of my Tiltbridge setup and may require further refinements for an optimal fit. The accompanying Fusion file allows you to make any...

Tool Bit Holder designed to hold 30 4 mm bits (5/32"). Print Settings Printer: Metamaquina 2 Rafts: NoSupports: No Resolution: 200Infill: 30 Filament: Filamentos 3D Brasil ABS White Notes: Very easy to print. ...If the holes come out too small, try...

Customized version of https://www.thingiverse.com/thing:3692202 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3692202

The majority of measurements were taken from the PCI Local Bus Specification Revision 3.0, while some dimensions were obtained directly from the physical component. However, we cannot assure complete accuracy, but it should be quite close to...

Customized version of https://www.thingiverse.com/thing:3692202 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3692202

Ein einfaches Schutzgehäuse für den Esp 32 mit dem Vorteil das die Pinout Belegung noch ablesbar ist.

TTGO Case for ESP32 OLED Display micro controller, flexible antenna

Options to Make it Happen: _depthLabel = -0.3 _thicknessOfWalls = 0.8 _fitBetweenWallsGap = 0.1 _bottomSurfacePart = bottom _labelIsAtThisHeight = 8 _textToPutOnLabels = (left blank) _columnsOnWhichTextIsWritten = 1 _heightInsideBottomHalf = 32...

I designed a PCB with Eagle, assembled all components, wrote the code and created this custom case from scratch. The case was printed using PETG. All of the ESP's data is transmitted to Thingspeak in real-time through a seamless connection. Check out...

Case design for a Clumsy MIDI, mt32-pi + Raspberry Pi 3A, with a 0.91" OLED display, rotary encoder and 2 tact buttons. Printed in regular PLA, .2mm.  Highlights painted on (badly). ... Decided to use the original rotary knob encoder on used model.Board...

Case design for a Clumsy MIDI, mt32-pi + Raspberry Pi 3A, with a 0.91" OLED display, rotary encoder and 2 tact buttons. Printed in regular PLA, .2mm.  Highlights painted on (badly). ... Decided to use the original rotary knob encoder on...

This is intended for tiny 4mm 5/32 inch hex drive bit storage.

This designs purpose is to holder the insert from a Bosch Professional 32 pcs Screwdriver bit set on the Ikea Skadis peg board I selected this bit set as it was nice and compact with a nice insert which could easily be removed. ... Link to bit set used:...

I'm going to keep the same message without changing it.

1/4 Inch Hex Bits: [A] (has Lid) 10.6mm High 0.6mm thick base (3 layers @0.2mm Layer Height) +10mm 1.6mm wall thickness [A] Tiered (has lid) 10.6mm to 18.6mm High in 2mm steps 0.6mm thick base (3 layers @0.2mm Layer Height) +10mm 1.6mm wall...

Dieser Bit-Halter erweitert das WERA Tool-Check PLUS mit 5/32 Zoll Bits. Ein Adapter ¼ auf 5/32 gibt es hier: https://www.amazon.de/dp/B07VQV7WHD?ref_=cm_sw_r_cp_ud_dp_T1_Q6JWW258ZNTDAM6QQRMMDie Aufnahme für den Adapter gibt es hier:...

Helpful instructions and board pinouts can be found at https://www.instructables.com/id/Configuring-MKS-Sbase-V12-32-bit-Controller-Basics/. 6. I've included my Smoothieware configuration file (config.txt). 7. And Startup code that I put in Slic3r...

Replica of original DeWalt 25mm bit holder for Tough case System

I made my own drill bit case for metric bits inspired by AnansiTheArmadillidiidae's case. Made it stronger, does not require supports. ...Simply fill the drill bits array, or use my choise ;-)

Minimal Magnetic Leatherman Bit Case Magnetic tape used to hold bits in place found here: https://www.acehardware.com/departments/home-and-decor/office-supplies/tape/22021

I upgraded my DeWalt cases with brand-new bit holders that utilize a clever diagonal rotation system, making it effortless to extract the bits. ...I created these custom replacements for my outdated cases, and they're working out fantastically!

Storing a set of metric drill/tap combination bits just got easier with this compact case. Any 1/4" bit shorter than 70mm and less than 10mm in diameter fits perfectly inside, making it an ideal storage solution for your workshop or garage. ...The case...

This protective casing for the Micro:bit ensures secure attachment to various objects using glue or tape, while also simplifying the process of attaching the Micro:bit itself. The bar provides a snug hold on the Micro:bit via tension, allowing for...

Self-Centering Drill Bit Case for BOSCH CC2430 3-Piece Clic-Change 1/4 In. ... Assorted Sethttps://www.amazon.com/gp/product/B0000TZX1M

Created labels to fit this LLT Screwdriver 12 Bit Case Could add more if requested, these are just the ones I owned.

Screwdriver bit holder for cassette tape cases. Has a place where you can glue small magnets to the underside, so that the bits won't fall out when flipped over. It's a tight fit, especially with the J-cover. Uploading in case someone else finds...