algot skadis 3d models

Customized version of https://www.thingiverse.com/thing:5388605 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5388605

This trench creates a pocket for surplus water to collect beneath the earth's surface. ...A notch at one corner allows for easy monitoring of potential water buildup.

Customized version of https://www.thingiverse.com/thing:3765603 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3765603

Twist fit support mounts the same dimensions as the IKEA original ones, available as screw to the wall (hole in middle) or 'twist fit' - no screw required. Takes up 1 slot on the board. Allows the middle to be supported when heavier items...

Inspired by Affi's TS100 clip, which unfortunately didn't translate well to my printer. The clip surrounding the TS100 in this remix has been reinforced, and reorganized for better meshing. I've also added a smaller arm to provide additional support...

Customized version of https://www.thingiverse.com/thing:3765603 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3765603

<p>Use a more flexible filament such as PETG, I would not advice using PLA or harder as the flexing is crucial to the model.</p><p>&nbsp;</p>

Customized version of https://www.thingiverse.com/thing:2535312 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2535312

Modification to increase Hook Size.

Customized version of https://www.thingiverse.com/thing:3976770 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3976770

Customized version of https://www.thingiverse.com/thing:3976770 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3976770

I liked Nifnifs file, but found the stand failed on the upright due to the weight of my Funko Pops. ...I reduced the weight and thickness of the stand and ran a longer universal hook through the stand and it has been working better for my heavier...

Customized version of https://www.thingiverse.com/thing:3976770 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3976770

I noticed my initial file was uneven on both sides, rendering it unsuitable for use. I successfully merged the pieces together using Meshmixer, but when I converted the mesh into a solid object, the shapes didn't match their original forms perfectly....

i designed it to clear up space that my rods where taking everywhere. ... the spin rod holder is 25mm diameter and for the fly rod holder it is 32 mm in diameter

<p>This is a redesign of the large/small cable holder from https://www.thingiverse.com/thing:2853257.</p><p>They are based on the design, but have a distance of 4 mm between the fingers which are 4.5 mm wide.</p><p>Two of the original universal hooks...

<p>This is a holder for the Incr T-Rule that fits the SKÅDIS pegboard from Ikea. It allows you to store your Incra T-rule on top of the pegboard without it falling off. ...It includes two holders for mechanical pencils.</p>

Customized version of https://www.thingiverse.com/thing:3765603 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3765603

Cotton Swab Holder 64mm Compatible with IKEA Skads

Print standing (open side of the Cartridge facing up. ... I've printed with support and 10% infill on a Anycubic Kobra.

different designs that fits different calipersmitutoyoTesaDiesellaand maybe more :-)

Customized version of https://www.thingiverse.com/thing:4042873 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4042873

A nice storage for all those creditcard-sized membership-cards lying around. Holds up to 10 cards. Printing upside down without supports worked fine. ... Print Settings Printer: Prusa mini+ Rafts: NoSupports: No Resolution: 0.2mmInfill: 20% Filament:...

I made few modifications to the original version: - Holder is a little bigger so it fits with a case like the one in the picture. - Removed in the rear part of the model so the buttons do not touch the holder. - Removed part of the front, enough...

<p>Print settings:</p><p>Material: PLA</p><p>Layerheight: 0.2</p><p>Infill: 15%</p><p>Support: If you print it face down, you'll only need a very small support for the hook.</p><p>Printed it in 17 minutes, its a very snug fit.</p><p>Hope you like...

<p>I designed these cups a while ago but just decided to upload them. There are 2 different sized cup holders, and 3 different sized cups.</p><p>The Small holder holds the small cup, and the large cup. Small cup is the perfect size to hold a few...

Enjoy this glue holder!