alien antenna 3d models
32389 3d models found related to alien antenna.thingiverse
Alien Antennae were created by Matt. Instructions To attach to headband, stretch and place through the T-slot, then turn so it lays perpendicular. ...For best results, print with the following settings:...
thingiverse
A derivative of my normal antenna mount, but with the two rx antennas pointed in opposing directions. Designed to fit the 5" Alien frame from ImpulseRC. ...Intended to be printed in a flexible filament, like TPU.
thingiverse
... a 6" Alien frame. ...Bushings are included for using this with my vtx / rx mount, as well as by itself. Other 6" Alien parts: VTX RX mount https://www.thingiverse.com/thing:3323089 Runcam Swift 2 side plates https://www.thingiverse.com/thing:2904397
thingiverse
Simple antenna mount for the Impulse rc micro Alien
thingiverse
A replica Apex antenna clamp for your Alien! Use (2) M3x6mm bolts to hold in the antenna. ... There's two models depending on what stand-off sizes you have: - 10mm you'll need: (2) 25mm stand-offs + (2) M3x15mm bolts (min) - 15mm you'll need: (2)...
prusaprinters
Its pretty tight, but the result is, that your Antenna wont move! I created different versions for different SMA Connectors! added GPS Mount for this GPS Module added another SMA Version added flat surface version of "SMA Version" to print upside...
thingiverse
- added GPS Mount for this [GPS Module](https://www.banggood.com/7M8M-Ublox-M8N-GPS-Module-for-APM-Pixhawk-CC3D-Naze32-F3-Flight-Control-p-1078657.html?p=3R26141006882201412N) - added another SMA Version - added flat surface version of "SMA Version"...
thingiverse
This antenna mount was designed for the Alien 4". ... Print Settings Printer: Wombot XL Rafts: No ...
thingiverse
Post-Printing Cleanup The support pattern will make your alien look like he's got a rash behind the antennae dishes unless you do a little cleanup. Personally, I think matte is a good finish for these, so I'm just sanding my ABS prints, not doing...
thingiverse
Antenna mount for the impulseRC Alien frame. Best suited for pigtail with screw-mount, but also works without screws. ... Printed with 100& infill.
thingiverse
Designed this alien antennas to fit your sony wh-1000xm3 headphones. Print two, add two of them to your headset and they add unlimited reception and space to tie those airwires when not in use. Oh yeah... you can also tie your facemask to it...
thingiverse
Holds 3mm Antenna tubes. ...28mm spacing for quads. Designed to stack all together with a U.FL AXII, HellGate Buzzer and antenna tubes. Buy it here >>>>> https://www.wickedquads.com/collections/3d-printed/products/alien-antenna-tube-mount
thingiverse
Added: New file for 25mm on center standoffs This is an rx antenna mount for the Impluse rc alien 5" frame. It lowers the antenna down to the lower deck, so as to fit larger batteries. Also included is a version that allows for an led strip to be...
thingiverse
This is a antenna mount for the impulse rc alien 5" frame. It mounts to the rear set of mid frame posts. Ideally it is intended to keep the antennas closer to the center of the frame so that when you fly with a lot of camera angle your antennas are...
thingiverse
This small plate lets you run your coax lead away from the carbon fibre frame.
thingiverse
Remixed to fit the slammed Alien top plate to bottom plate with 45 Degree angle on the Mount
thingiverse
Customized version of http://www.thingiverse.com/thing:400638 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=400638 Instructions Using the following options: Age = 7 Shell = no Flat = no Ribs = no Antennae = no
cults3d
... is a rough combatant capable of withstanding all kind of punishment. This set includes: Antenna Alien MB Stl Antenna Alien MB Pre-Supported Files - Chitubox Holobase (designed to be printed flat on the plate with easy removal and no elephant foot)
cults3d
... pilot knows the model and maker of any starship with just a glance. This set includes: Antenna Alien FC Stl Antenna Alien FC Pre-Supported Files - Chitubox Holobase (designed to be printed flat on the plate with easy removal and no elephant foot)
thingiverse
Mounts onto rear standoffs and angles VTX antenna at 30deg. ... 29mm standoff center to center heigh 13mm 5mm standoff holes
thingiverse
Crossfire and video antenna holder for the 5" ImpulseRC Alien
thingiverse
Foldable antenna mount for ImpulseRC Alien 5" For the assembly you will need these items: 3x M3x10 1x M3x25 2x M3 nut 2x antenna tube (outer diameter 3mm, inner 1.5mm or 2mm) There are two versions of the moving part, one is flat and a second is...
thingiverse
I am presenting you a great antenna mount for your Impulse RC Alien 4" frame. I do recomment you to get the TBS SMA to U.FL cable and go for the V3 version! By that you enable cablemovement and broken SMA cables because the SMA is fixed in its...
thingiverse
This is a VTX antenna mount to hold the antenna in place when you run your VTX above the flight controller. It mounts to the pressed in nut in the upper frame plate. Thus it is only useful if you are not using the rx antenna plate as shown in...
thingiverse
Spacer kit designed to allow a little more breathing room in that very tight stack (+3mm). ...Also includes rear XT30/VTX/RX antenna holder,
thingiverse
Impulse RC 5" Alien rx antenna tube holder. ...Print in Tpu upright at 30% infill and glue antenna tubes in.
thingiverse
Mount Antena T for Alien Frame. ... I use it with cable ties and heat shrink Layer Height = 0.2 mm Infill = 20% - 40% Material = PLA Plate Adhesion = Brim Support = None