alien frame 3d models
113586 3d models found related to alien frame.thingiverse
Mobius Holder Alien Frame Mobius Holder for Alien Frame and clone with 30 degree angle. ... Layer Height = 0.2 mm Infill = 20% - 40% Material = PLA Plate Adhesion = None Support = None
thingiverse
Battery Cable Holder Alien Frame Good for blocking cable on one side of the drone avoiding collision with props.. ... Layer Height = 0.2 mm Infill = 20% - 40% Material = PLA Plate Adhesion = None Support = None
thingiverse
Mount Antena T for Alien Frame. ... I use it with cable ties and heat shrink Layer Height = 0.2 mm Infill = 20% - 40% Material = PLA Plate Adhesion = Brim Support = None
myminifactory
This part is designed specifically for the Alien Frame 5 or 6 inch and will slide over standard circular pillars (35mm tall) for the frame top plate. The tilt on the camera is 35 degrees and the camera will be press fitted in, holding it very...
thingiverse
A front bumper for the ImpulseRC Alien frame. Works with the 4, 5, and 6 inch frame variants. There is open airspace between the front of the frame and the front of the bumper providing impact damage mitigation. Locks (with a positive snap) onto...
thingiverse
HS1190 camera mount for Alien racing drone Remixed. Thanks to tsyken. ...Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
VTX Antenna holder for Alien 5" Frame You can use for may VTX , but this works perfectly with TBS unify
thingiverse
I bought a clone of the ImpulseRC Micro Alien frame from Unmanned Tech but the side plates used to hold the camera were a little too small which resulted in a shaky FPV feed. I took a picture of the part of my phone, converted it to .svg and the...
thingiverse
miini Alien frame for 8.5 mm motors max prop size 65mm this frame has not been tested is scaled up from my 7mm miciro frame still have to make camera mounts and changes build at your own , use CA glue to glue the frame look at my micro MRZ for...
cults3d
... durable, less flexible ! ... V2 : Lighter and smaller ! Somebody should help me to make top plate and add it to remixes :) Alien copy frame for 6x15mm motors screw holes for Furibee F36 main board (Should also fits E010, E011, H36, H67, Inductrix )
thingiverse
... less flexible ! ... - V2 : Lighter and smaller ! - Somebody should help me to make top plate and add it to remixes :) - Alien copy frame for 6x15mm motors - screw holes for Furibee F36 main board (Should also fits E010, E011, H36, H67, Inductrix )
thingiverse
Since I didn't like the fairly flimsy GPS-on-a-stick mounts, and had no special spot to mount them on on this frame in the first place, I decided to make a GPS tower to fit. It will take 2 M3 screws to attach to the existing holes at the back. The...
cults3d
Since I didn't like the fairly flimsy GPS-on-a-stick mounts, and had no special spot to mount them on on this frame in the first place, I decided to make a GPS tower to fit. It will take 2 M3 screws to attach to the existing holes at the back. The...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/7Zvs2PK7b5m remix of http://www.thingiverse.com/thing:1595244 for brushed f3 evo, 8mm motors, DSM2 satelite and Eachine EF-01
thingiverse
This part is designed for my Alien frame from Impulse RC. Camera angle: 30 degrees. ... Longer M3 screws should be used for fixing to frame.
thingiverse
Hero 4 Mount for Impulse RC Alien extremely recommend use Freedom 360 nd8 filter for protection https://freedom360.us/shop/nd8-filter-kit/ and a side strap for security https://www.getfpv.com/lumenier-xl-lipo-strap-rubber-grip.html Print on TPU...
thingiverse
Micro Alien frame for Scisky flight controller 7mm motors , Nano QX 52mm propeller Fx798T camera printed in ABS look on my micro Mrz frame for instructions some changes in the works average 7.8 grams Print Settings Printer: raise3d n2 and n2 plus...
thingiverse
Additionally I designed the angles for mounting onto Alien frame 5". I used two 2,5 x 10 mm and two 2 x 5 mm screws to mount the camera to the Alien 5" frame. It's designed to work without nuts! Thanks to the guys from Rotor Riot for their...
thingiverse
Customized version of http://www.thingiverse.com/thing:1068400 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1068400 Instructions Using the following options:...
thingiverse
Design part for the MartianII / Alien frame. ...(Inspired by Banggod from Catalyst Machineworks)
thingiverse
* NEW V2 Alien inspred frame - 8.5mm coreless motors - Board and battery attach with rubber bands or with velcro
cults3d
NEW V2 Alien inspred frame - 8.5mm coreless motors Board and battery attach with rubber bands or with velcro
thingiverse
Click on case for Martian II / Alien frames Printed on a RF1000 Layer height: 0.15mm You can also print it with the flat surface on the printing bed