alignment tool golf 3d models
139348 3d models found related to alignment tool golf.thingiverse
Golf ball alignment tool to draw a straight line on a ball with a sharpy.
thingiverse
Simply put the tool on the shaft of your golf club, just past where your new grip is/will be, with the "sight" closest to the head of the club. Then, look down the "sights" and line one of the inside edges up with the bottom groove/line on your...
thingiverse
Golf ball alignment tool. quick and easy to print. I found that printing this laying on its side with supports turns out the best. Works perfect with "Sharpie Fine Point" markers. I also use 100% infil since it's thin and needs the strength. I've...
thingiverse
I designed this golf ball marker guide to use for straight lines on the golf ball for putting. I personally orient the print so that the opening/inside of the marker is down to the build plate, that gives a better finish on the outside. ...I also use...
thingiverse
This is an alignment tool to setup and align your shifter in your GOLF MKII. Just for 020 5-gear gearboxes. There should be some tutorials on YouTube how to use it. Feel free to send me a small tip for my time. ...I always appreciate it.
thingiverse
Do you like the Callaway ERC golf ball alignment lines but don't want to shell out $50 for a dozen of them? Print this! Please be aware that you'll probably need to mess with your slicer settings to get this to print right. I went through 4 copies...
thingiverse
IT IS IMPORTANT that you print it lying on one side (or in some other thought-through way) to ensure that the layers are adjusted in a way that the alignment tool can easily flex when you snap it onto the golf ball. Make sure that the printer mostly...
cults3d
This is a redesign of the ball marker by Chuck Hellebuyck Elproducts (http://www.thingiverse.com/Elproducts/about)
thingiverse
This is a redesign of the ball marker by Chuck Hellebuyck Elproducts Print Settings Printer: Wanhao i3 Rafts: No ...
prusaprinters
<p>This is a redesign of the ball marker by Chuck Hellebuyck <a href="/Elproducts/about">Elproducts</a></p> <p>This one didn't print great, but it works good. If anyone tries a different print orientation please leave a comment with your results.
cults3d
This is a redesign of the ball marker by Chuck Hellebuyck Elproducts (http://www.thingiverse.com/Elproducts/about) This one didn't print great, but it works good. If anyone tries a different print orientation please leave a comment with your...
thingiverse
This is a redesign of the ball marker by Chuck Hellebuyck Elproducts This one didn't print great, but it works good. If anyone tries a different print orientation please leave a comment with your results. Flat on the bottom with a brim works, but...
thingiverse
I have found a few of these over time, and all of them seem to error on the side of form over function, and are just giant pain in the butt to print. This has a larger flat base for good adhesion, and less curves to make it super simple to print and...
thingiverse
Carefully align the tool to the golf club head using the sight lines on the tool. Remove the existing grip and install the new one. There is a vertical line sight line to line up with the leading edge of the club, and horizontal sight lines to line...
thingiverse
A must have golf accessory, not sure how close it is to the real thing but I wasn't going to pay £12.
prusaprinters
If you have an alignment stick, you can use it as an easily adjustable, super steady phone stand with just a simple clip for your phone!The clip pictured and the files attached fit a 78.5x10ish mm cross section phone (such as most recent, standard...
prusaprinters
This is used to indicate where your golf club face is during the golf swing. A 20mm X 3mm neodymium magnet is glued to the part. This is not intended for full-speed swings. ... </p><p> </p><p> </p>
sketchfab
Quadrupole alignment tool for API 5500 series mass spectrometers.
thingiverse
Basic Solar Panel alignment tool use TPU for travel/portable solar panel
thingiverse
Clutch alignment tool for Ural Motorcycles, worked for a 2010 Patrol model.
cults3d
Here is a tool to align more easily the ailerons on a rocket of 18mm and/or 24mm diameter Here is a tool to more easily align the fins on a rocket with a diameter of 18mm and / or 24mm
thingiverse
Tap alignment tool. Helps to keep tap square to work surface. ...9.6mm ID for stem of tap