aluminum 8020 3d models
25803 3d models found related to aluminum 8020.thingiverse
This is designed to friction fit into the slot of 8020 and other variants. It creates a nearly flat surface along the two faces between the slot. ...Can be easily extruded to any length.
thingiverse
This fits 1" aluminum extrusion, tested specifically on TNUTZ (https://www.tnutz.com/product/ex-1010/) SCAD included. ... Sized provided are: 10mm 15mm 20mm
thingiverse
A cap to be put on the ends of an 8020 1010 extruded aluminum beam. ...Protects surfaces from getting scratched by the beam.
thingiverse
- 25x50mm outside bracket, takes 4 [M6x25mm countersunk bolts](http://amzn.to/2vSrcoo) - 25x25mm outside bracket, takes 2 [M6x25mm countersunk bolts](http://amzn.to/2vSrcoo) - 25x25mm inside bracket, takes 2 each [M6x12 button...
thingiverse
I run two of these high power Fosi mini amps along with four Aurasound bass shakers on my sim rig setup to increase immersion with low frequency effects while sim racing: - 2x Fosi Amplifiers:...
thingiverse
I needed a VESA mount for my car simulation rig and came up with this design. ... Mounts to the 8020 require M8x16 bolts. ... The holes closer to the monitor are recessed.
thingiverse
I remixed this from a well designed end cap, but it was not fitting in my 8020 10-series extrusion. I pulled in the slot tabs a bit but left the cap end the same. ...I scale this to 25.4mm in X and Y and 10mm in Z to fit onto a 10-series extrusion from...
thingiverse
3D printable t-slot cover for 25mm 8020 aluminum extrusion, based off of 8020 part number 25-2112, found here. Use it to manage or hide wires, or just make your t-slot extrusions look better. 3D printed pieces work surprisingly well. STL model is...
grabcad
8020 aluminum extrusion profile from 8020.net. This is part number 2012 and 2 inch by .5 inch in size. ...This is 1:1 scale accurate model from from their blueprints.
thingiverse
This is an alternate hanger for use on horizontal 8020 series 1010 extrusions. It clips into the extrusion and makes it easy to hang an ornament or a utensil from the extrusion. Unlike the last one which held the dangling item at the front of the...
thingiverse
Remix of the previous file for M8 bolts
thingiverse
Remixed to create a single end cap for the 2080 Aluminium Extrusion on my custom-built Macro Sliding Rail.
thingiverse
In an effort to reduce costs on my Wilson i3 build (made from 20mm 8020 extruded aluminum), I started looking for alternatives for the rather expensive m5 T-slot nuts used in 20x20mm extrusion. I attempted standard square m5 nuts (too tall),...
thingiverse
Simple RAMPS 1.4 mount for 25mm 8020 aluminum extrusion. Mounts to Arduino Mega 2560 and RAMPS, which I bought together on Amazon in this 3D printer electronics kit. Keeps all electronic connections exposed for easy access and good cooling of...
thingiverse
This will hold a standard #10 nut in 80/20 aluminum structure. You might find it to be a little sloppy if printed at higher quality. I designed it to print in Draft mode...quick and dirty. ... Spacing is on 1" centers.
thingiverse
I made it to attach at a 45 degree angle onto 25mm 8020 T-Slot Extruded Aluminum. Hardware Needed 4 M3x25 screws (I only had 3 in my pictures) 4 M3 washers and nuts 2 each M6 bolts, washers, and T-Nuts for your aluminum extrusion. I used 12mm bolts...
thingiverse
Remixed to create a single end cap for the 2080 Aluminium Extrusion, on my custom-built Macro Sliding Rail. ...This 2nd version has horizontal V-Slot supports, as it works better with my custom Macro Rail Slider.
thingiverse
Monitor mount for 40 series extrusions (4040 and 4080). Remixed from the previous model for monitors with a recessed mounting hole. ...220mm deep from the monitor holes to the start of the extrusion.
thingiverse
Great mount for 80/20 15 series Sim Racing Rigs. Just clips into profile slot. Very secure. ...Used on my motion rig.
cults3d
A collection of parts useful when modeling and printing extruded aluminum. ... Specifically 8020-1010 gussets, coupler, endcap, arduino clip, bracket etc.
thingiverse
A collection of parts useful when modeling and printing extruded aluminum. ... Specifically 8020-1010 gussets, coupler, endcap, arduino clip, bracket etc.
thingiverse
Aluminum Extrusion Mount for Inateck HB2025AL USB 3.2 Hub I use it to mount the USB Hub on my sim rig's aluminum extrusion (8020).