am3 to am4 adapter cooler 3d models
2162356 3d models found related to am3 to am4 adapter cooler.thingiverse
I needed a cooler for an old AM3+ motherboard, and all I had was an AM4 era stock cooler. So I made this system to adapt the two. This is designed to be used with M3 heat inset threads added to the backplate, with screws to match. ...I using 10mm...
thingiverse
You need, to remove stock amd mounting things. ... keeping backplate remove front plastics and put the new piece with stock screws.
thingiverse
I couldn't find any aftermarket coolers for this socket so I decided to design brackets for it to use AM3/AM4 coolers which uses hooks to secure the cooler to the board. You'll need to print 2 of these with 4 M3x14mm screws Because of limited space...
thingiverse
This is some simple adapters for using an AM3 heatsink on a AM4 motherboard. Specifically created for the Arctic Cooler A11. Works on an ITX motherboard with components close to CPU. ... Make sure you print on high heat material such as ABS.
thingiverse
I designed this mount for older cpu coolers standardized for 939/AM2/AM3 on AM4 motherboards. I changed my original "AMD Wraith Stealth" cooler for bigger (older type) which i found home from older computer "Arctic Cooling Freezer 64 Pro". Easy to...
thingiverse
https://www.thingiverse.com/thing:3531498 I simply raised the area around the holes for the AM4 screws by 1mm because I found it hard to install due to the cooler popping out the other side when you screw one side in. ...This gave it more hole to screw...
prusaprinters
A minimal adapter to take your Intel LGA 115x socket coolers and put them onto AMD AM4 socket CPUs.For the AM4 side, screw in like normal, on the LGA115x side, use M3 nuts and bolts to secure.DO NOT print this in PLA! <strong>PETG</strong> or...
thingiverse
LGA2011 adapter for mounting AMD AM2 AM3 AM4 cooler. Designed for Kllisre x79h motherboard. ...8mm screws.
thingiverse
AM3 & AM4 *use Intel hardware for mounting (thumb-nuts, standoffs and screws) 28OCT18- Updated the design to allow for the Corsair Link cable to be plugged into the pump...my earlier revision did not have the "cut out" needed to fit the cable. I...
thingiverse
Hallo, ich hab hier mal ein Adapter entworfen um z.B. ...AM4 Wasserkühler auf ein AM4 Board zu verbauen. ... Das Teil einfach 2x ausdrucken und mit M3 Zylinderkopfschrauben direckt in das Kunstoff schrauben.
thingiverse
... and M3 nut with 3 notches. ... Standart #6-32 nut (5/16" wrench) is too big for 939 frame geometry, and M4 bolt can be too big for holes for #6-32 (3,5mm) in cooler clip too, so I prefer M3. ... Back pocket is more stronger instead side pocket also.
thingiverse
This adapter lets you replace that noisy 80 mm fan on the stock AM3 cooler (which is also compatible with Ryzen CPUs using the AM4 socket). The adapter clicks into the place of the original fan. ... I have printed it with HT PLA, and it didn't melt at...
thingiverse
This is an adapter that screws in to the LGA 2011-3 mounting holes for the X99 platform and allows you to mount an AM4 cooler, specifically an AMD stock cooler.
thingiverse
Remix of AM4 adapter posted bypelelademadera. All credit to him as I only modified his 3dm model in fusion 360 to fit my motherboard - MSI x570 Tomahawk with EKWB Supremacy EVO water block. I have included f3d file as well. ... Ill try to update with...
thingiverse
Adapter for installing a cooler with a 115x mount on an A4 motherboard, minimum size, screwed with original bolts, I used 4*20 mm screws to mount the intel cooler, with a 6.5mm wide cap
thingiverse
This is a am4 adapter for EVGA CLOSED LOOP CPU COOLER 120MM
thingiverse
Custom adapter for 939/754 cooler to am2, am3, fm1 or fm2 socket or instead original frame. Adapter-hook. Can use instead of original plastic frame or as adapter for old cooler, that have only 939/754 socket bracing (look at photos). Model for 3D...
grabcad
... ...Can use instead of original plastic frame * or as adapter for old cooler, that have only 939/754 socket bracing (look at photos).Model for 3D printer. ...Verified by printing with PLA plastic.* Like this Bracket for AMD sockets: AM2, AM3, FM1 or FM2
prusaprinters
But I liked the powder coated plate to much so I decided to make adapter brackets so I could keep using the original plate with slight modifications. The original plate needs to have some pars cut-off or drilled shown in one of the images. For...
grabcad
Top plate to adapt Ybris Eclipse from original s775 or s1366 to either AM3 and AM4 sockets.NB: Was 3D printed, ABS and 75% filling and successfully tested on AM4. ...For reducing bending, thickness can be increased, however I prefer it like this as it...
thingiverse
... it with M3 screws, washers at plastic surfaces and nyloc nuts. The original backplate can be used or a printable version needs to be sourced somewhere else. Source files for Design Spark Mechanical are available. ... Part Status: Approved
thingiverse
@med145 's wonderful bracket adapter (https://www.thingiverse.com/thing:2238848 - The attribution field was broken at the time of upload), but, includes the standoffs so that the STOCK backplane + screws can be used, without any sort of standoff...
prusaprinters
The screws should sink into the holes, and grab the backplane threads perfectly, and keep the CPU nice and cool. I'm using this with a Corsair H50 from 2017, but other models are likely extremely similar. NOTE: Please re-download if you downloaded...
thingiverse
I design the holder for Cooler Master Seidon 120v for AMD AM4 sockets because in the Cooler Master store the official adapter is out of stock. I used PET-G but is possible to print with ABS, I don`t recommend using PLA Note: I used the screws...
thingiverse
Default AM4 backplate used with AMD Wraith cooler. No threads, Wraith cooler screws with self-thread. ... Lite is the one with bigger hole
thingiverse
If you want to have a little bit more pressure to be certain, you can shave off about 0.5mm from the Cooler Mount file from the bottom, as well as from the top of the mounting plate screw holes, but your printer might do better than mine (I might...
thingiverse
CoolerMaster MasterLiquid 240 Mounting Kit AM3 AM4 LGA775 LGA115X
thingiverse
On the first run, I used PLA and it warped / popped the cooler off (this was mainly due to the fact I forgot to plug in my CPU fan... whoops). ...I'd only use this as a temporary solution if you're desperate and are waiting for a stock one to come in...