amiga 2000 3d models

One of the 3 back panel case fillers of the Amiga 2000 computer.

One of the 3 back panel case fillers of the Amiga 2000 computer.

This is my design of the little LED panel in the top-left hand corner of the Amiga 2000 front. ...It is based on pictures of the original panel.

Amiga 2000 - TF536 in co-pro slot top bracket. Fixed by a single bolt at the front. I used 3x3x4 brass insert, heated and pressed in. ...(nut and bolt would also suffice)

This is a bracket for a TF536 card mounted on a CPU relocator card for the Amiga 2000. The CPU relocator card is "Amiga 2000 CPU Adapter V1" from Matthias Münch. The bracket is created for this combination only! The bracket will make sure the...

This is a brace for the arananet (arananet.net/pedidos/) 68000 dip socket to cpu slot adapter that relocates a vampire 500 v2, Terrible Fire 530 and others to the cpu slot of the amiga 2000 the adapter rotates the vampire by 90 degrees to face the...

I purchased a Gotek for my Amiga 2000 from RetroFriends and needed a simple yet sturdy means to mount the drive in the second drive slot alongside the factory floppy drive. This frame mirrors the size of the factory Chinon drive. The Gotek I...

I purchased a Gotek for my Amiga 2000 from RetroFriends and needed a simple yet sturdy means to mount the drive in the second drive slot alongside the factory floppy drive. This frame mirrors the size of the factory Chinon drive. The Gotek I...

Expansion card bracket for the Amiga 2000

Amiga 2000 shaped SD Card Holder. ...3 different models.

Replacement blanking plate for the lower 5.25" bay on an Amiga 2000

This is another 80mm Fangrille specialized for the Amiga 2000. ...Print Settings Printer: Anet A8 Rafts: No ...

I created this to replicate the CD bay cover of Amiga 2000 computers This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fREvFP6zP6l

Halterung für Mini ATX Netzteile im Amiga 2000 Es muss eine Drahtverbindung vom Gehäuse des Amiga bis zum Mini ATX Netzteil gelegt werden um die Schutzleiterfunktion zu gewährleisten. ... Mini ATX Netzteil sollte -5 V liefern

This is a rear slot cover for the large slots used in the Amiga 2000. (i.e. Video Slot and CPU Accelerator Slot) This is not to be confused with the ISA/Zorro slot covers. ... Fell free to remix this slot cover so you can customize cutout holes for...

Used to make a normal size drive look right in the slightly taller Amiga 2000 drive bay. Includes the 12mm standoffs to bring the drive to the correct height. Note: Gotek drive has a slight notch in it. ... Also Note: Ive found some drive vary in...

This piece of hardware will fill the gap leaved by a Gotek floppy emulator (or another standard floppy drive), on Amiga 2000 floppy bay window. it can be placed under the floppy or over it. This thing was made with Tinkercad. ...Edit it online...

Since is now almost impossible to find theese little spacers to mount a floppy drive or a gotek grive on Amiga 2000 i created it! they have a hole to let the screw pass so you actually need a longer screw to tighten a floppy drive or a gotek drive. ...

Nothing special else, the brace helps to stabilize the adapters used in the Amiga 2000 CoPro Slots e.g. form Arananet made for the Apollo Vampire Accelerator. Prints without support if put flat on the top side. Works like a charm as far as I can...

Just a couple of useful bits for putting a Mac 3.5" drive inside an Amiga 2000's 5.25" drive bay, for use with the AMAX emulator. The drive rail is used for mounting the mac floppy drive in the drive bay. It has been designed so that it can be...

Edit it online https://www.tinkercad.com/things/0VjFUWAk5MR This is a highly accurate model of an Amiga 2000 Floppy Drive Bay Cover that I created from scratch in Tinkercad using measurements from a real Amiga 2000 Floppy Drive Bay Cover. Please...

I remixed this cover plate to give it a little more support when connecting the VGA cable to the back of the Amiga 2000. The original file seemed a little too flimsy for my comfort when a thick VGA cable was connected to it. ...This works well with the...

Searched for a brace for my Amiga 2000 Cpu Adapter V2.0(designed by Matthias Heinrichs). Only found one that looked like it could fit, but it was too long. Long story short, this remix is only 59mm long. I screwed it with a M3x15 hex bolt direct...

Provides easy access to both devices with sacrificing both 3.5" Floppy Drives for the Commodore Amiga 2000. Mount boards with regular "hard drive" screws. ... If you love this, please send a donation: PayPal - paul@anotherworld.com.au Bitcoin -...

Amiga 2000 Vampire HDMI & MicroSD holder backplate, the microsd is a firm fit but clips in not to be printed for sale on ebay! ... had a few people have issues finding the hdmi adapter i used this is the exact one i modeled this for...

Este montaje es para instalar una Gotek en el hueco de la bahía de 5.25" del Amiga 2000. ...el soporte se adhiere al frontal con un poco de adhesivo, y el frontal se atornilla en su lugar, la pantalla OLED es de 128x64 1.3"

Amiga 2000 rear slot cover to pass through the Raspberry Pi 3B+ ports: Micro SD card, 2x USB and HDMI. The Micro SD card reader is just press fitted. ... The 3mm version was too flimsy with the filament I had available so I used the 4mm version to...

Amiga 2000 holder for a standard slider switch. Can be used to select Kickstart ROMs/banks for example. Doesn't require any drilling, everything is press fit and and is easly available fromt the front of the computer. ...Great alternative for rocker...

Amiga 2000 all in one vampire card backing plate to house lan, hdmi & microsd extension, the mount holes for the hdmi are 30mm apart and can be sourced from ebay not to be printed or remixed for sale on ebay! ... had a few people have issues finding...

I made this to place the Bi-colour led of kickstart switcher in place of the original power led of Amiga 2000 The original led is glued to the led holder and, this particular led holder is almost impossible to find... after printed you need to use...