amoeba extension 3d models

A robust pedal extension for GotWay MCM4, potentially suitable for other similar pedals from GotWay as well. These fare significantly better on average rides and the boots stability is compensated by printed male pins. Scrape off a little top...

I definitely liked the concept of adding something to that often unused extension port of the Kitchenaid stand mixer. Our Nespresso cup extension on our stand mixer has been in use for about six months now. By the way, there's even a hook to hang...

I built this cable extension protector to secure and protect the connection after my extensions failed due to stepping on, pulling on, and bending the cable connectors.\r\n\r\nIt fits the following cables and extender:\r\n\r\nCable Matters SuperSpeed...

So I modified the original extension and created three parts: a part that mounts to the light switch, an extension piece to lengthen everything, and then a pull ring that goes on the bottom. I use one of each part to get a good length for my...

My SD Card Extension Measured 35x11.5mm - Ensure Yours Fits This Dimension Before Printing. Four M3 (8mm Long) Screws Are Needed To Secure The Cover In Place. When Printing, I Oriented The Site Facing Downwards To Hide Support Marks After...

... spreader handle. Drilled holes in dowel & spreader handle to match lever connection pieces. Length of dowel rod will depend on mower and spreader. I used butterfly nuts for the lever connection so that the handle extension would be removable.

I can confidently say that when printed correctly, this extension can withstand quite a beating - mine has withstood no breaks or issues at all.\r\n\r\nTHIS EXTENSION WILL ONLY FIT STICKS WITH THE FOLLOWING DIMENSIONS: \r\n26 x 16 mm interior shaft...

The Nerf Triad-EX3's barrel length is increased by this extension, enhancing accuracy without requiring hand loading tools like a ram rod. It securely attaches to the blaster without adhesives and only requires removal of central pole supports. ...Feel...

I used Slic3R and 3D Builder to slice off the male and female parts of the spool halves in the original STL files, then fused them to make a male/female spool extension.\r\n\r\nYou simply print it and thread the coupler extension between the halves,...

A Baffle Extension for an Orion (GSO) RC 10 inch Trust tube scope, designed to mitigate the baffle design flaw presented by Leon Bewersdorff in his YT video: "Warning about GSO Ritchey-Chretien's Baffling ( RC resold under Orion, TS-Optics, ... )" ...

The extension have a height of 40mm and is intended for metal legs with a radius of 98 mm. I printed it in PLA and glue it with hot glue. ... Printer: Anycubic Vyper Infill: 40-50 % gyroid Layer Height: 0,3 mm Filament Material: ...

This custom-made extension boasts an impressive size of 84.46L x 54W x 19H and features a wheel opening of 49mm, perfect for navigating tight turns and capturing stunning shots from unique angles. ... Using Tinkercad, I brought this design to life...

This extension cord cover case features a robust shell design, with a custom internal structure, to prevent it breaking from being dropped or stepped on. ...It has a hinge to be able to open and close easily and snugly together to prevent weather from...

... in orca slicer.  If you've got a better way to get this piece made, I'd love to see it.  Future revisions might have longer hooks or maybe facing the other way or maybe hooks facing both ways to aid in getting the extension cord fully retracted.

One primary function of these extensions is to achieve the required distance between the lens and the slide without lengthening the slide holder. This is particularly necessary when using slide and cinema projector lenses. ... They are also valuable in...

elbow) - when they are dirty or may be contaminated this extension will help you. Designed in two sizes for different tap levers. To fix it: 4 x cable ties 4.6mm and a piece of rubber (bicycle tube) Print instructionsPrinted well with 0.15mm in PETG...

This is a remix I did, took a section of an entire plate and reduced it to the extension so it can be printed on an ender 3. The original file was too large and couldnt be split. I recommend laying this flat for the most strength, and printing it...

This is an extension for the G920 steering wheel pedals.\r\nIt should also fit a G29 and works with a flat 330mm steering wheel when using an adapter.\r\nThere are two types of arms that come pre-printed or laser cut specifically for this...

7.14.16: added extension arm2.stl as replacement part. Printed at 80% density. Self-locking nuts or thread lock will prevent the big end from coming loose. Warning: High temperatures (in a hot vehicle) can warp the mount, causing misalignment of...

A custom-built macro extension ring designed specifically for use with M42 lenses, allowing photographers to experiment with macro photography capabilities on their EOS 750D camera, paired with older M42 lenses. The ring was created with the...

Clips to hold your socket extensions to any magnetic surface such as the lid of a tool box. I super glued 8 mm diameter magnets to the back but other magnets would work too. These only work for Craftsman brand socket extensions. The diameter is...

This is an extension for Rainbird and Hunter sprinkler heads. They sell 6in long ones, but not anything between. There are a 1.5in and 2.0in extensions included here. These allow you to get the water above the grass where it is tall or the head...

Custom Xbox One Joystick Knob Upgrade for Smoother Gaming Experience Get ready to enhance your Grand Theft Auto and other game sessions with our modified joystick knob extension, designed specifically to reduce sensitivity for more precise control.

However, this fan exceeded the total height that the feet could handle, requiring an extension to accommodate it properly. To solve this issue, I printed four custom extensions using PTFE with 5% in the first 23mm and 20% for the rest in S3D, one...

the bike frame not allowing a mounting elsewhere The principle was therefore to create an extension to shift the support higher and behind the saddle. we fix this on the seatpost in 27 mm with two screws of 4mm . he original system is kept but...

This is an extension/spike for an ultrasonic solar powered dog repeller like this one (they all seem to be the same dimensions): https://www.amazon.com/AUDS-Ultrasonic-Deterrent-Flashing-Repellent/dp/B08R37BV54 Print it offset on the z axis to create...

... ...and with the extension act as a "spacer" for the cords.\r\n\r\nOverall length may change after barrel length testing is complete.\r\n\r\nv4 - removed unnecessary "legs" to keep spacer aligned. ... Added optional elastic travel path through spacer.

For a better understanding of how it works, check out this video: https://youtu.be/pK18BFSD1H8 You can find the recommended printer model here: Snapmaker 3D Printer, CNC, Laser 200mW and 1600mW To house your new module, you'll need an enclosure -...

... to close the screen door to reach it. I recommend a tiny dab of super glue or similar to hold it onto the switch. Over time it has a tendency to work its way loose. There are long throw and short throw extensions, depending on your needs.

... Update: March 11, 2017 - I added another version that uses 75mm. Print Settings: Printer: ANET A8 Rafts: No Supports: No Resolution: 0.25mm Infill: 15% Notes: This extension uses approximately 150 meters of filament for four pieces at 15% infill.