anafi tablet holder 3d models
337584 3d models found related to anafi tablet holder.thingiverse
10,1" Tablet extension holder for the Parrot skycontroller 3 (tablet thickness < 7mm). Designed for a Sony Xperia Z4 tablet (please, if any compatibility issue with your tablet, let me know). ... 28/10/2018 - V1 : new version for more stability.
pinshape
Watch the Picplease look at the pictures if you have this holder or you want to buy one. ...You can use this holder for Parrot Anafi then also at hubsan zino. Best regards NSGN.de nichtsinnvollgibtsnicht Instagram nichtsinnvollgibtsnicht Facebook
thingiverse
iPad tablet holder for drone controller. ...Skydio2 or Anafi Parrot drone May hold other tablets but is not tested. Can be easily modified to fit most tablets. Designed for use with optional lanyard. ...
pinshape
This commercially sold tablet holder for the Parrot Anafi can be used with this plate also on the DJI Mavic 2 and similar. ... Please look at the pictures if it is for you to use this holder and your Mavic, then print this plate :-) Best regards...
thingiverse
I needed a simple design to let me use my Amazon Fire HD8 tablet with the Parrot Anafi controller. This just clips on to the top of the tablet and allows you to insert the bottom of the tablet into the lower slot and the extension into the upper...
thingiverse
A remix of rgrfr's ANAFI phone holder (https://www.thingiverse.com/thing:4317589), which is a remix of PhilippeM's ANAFI 10" tablet holder (https://www.thingiverse.com/thing:3154873). This one is suitable for even larger phones (phablets) up to...
prusaprinters
A remix of rgrfr's ANAFI phone holder (https://www.thingiverse.com/thing:4317589), which is a remix of PhilippeM's ANAFI 10" tablet holder (https://www.thingiverse.com/thing:3154873). This one is suitable for even larger phones (phablets) up to 86mm...
thingiverse
This design is a drone holder compatible with Parrot Anafi Extended.
thingiverse
Anafi 18650 Li-on holder for battery case ,need more test for improve the system ,but work ! for experiment and prototype . ...Use https://www.amazon.fr/ruthex-Insert-filet%C3%A9-100-pi%C3%A8ces/dp/B08BCRZZS3 for terminal ...
thingiverse
Battery holder I made for charging in car. Enables hanging the battery from fabric pouch found in front seats of cars. ... Model should be printed upright.
thingiverse
This a 25mm filter holder for the Parrot Anafi. Recommended printing from TPU. It is a press on fit. Turn on drone and let camera calibrate before putting on camera lens. ...Calibration will fail with filter attached at power up.
thingiverse
Updates done: - upper corners were rounded to a wider angle - lateral edges thickness reduced by 1 mm - a semicircle was carved upper part of the front holder, so that it fits the housing of the standard ANAFI case. ... - I have splitted the model into...
pinshape
Anafi multi holder for landing gear Action cam holder and snow and floating skids. The landing gear or other parts not included! The multi Holder only is here to buy. Attention, these accessories should only be used with correct GPS reception! This...
thingiverse
So I took the tablet holder by PhilippeM, shortened and shaped it - to give this very secure fit. o You can run with this or knock it but the phone will stay in place o Fits a 79mm phone case o The holder securely locks in place o No damage to...
thingiverse
This is a quick remix of rgrfr's "Parrot Anafi - secure holder for big phone (see here: https://www.thingiverse.com/thing:4317589) and MattMGN's "Parrot ANAFI / Skydio 2 - Joystick Controller Protection (see here:...
thingiverse
Simple low profile tablet/phone holder for devices that are 7-10mm thick
prusaprinters
Simple low profile tablet/phone holder for devices that are 7-10mm thick Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Category: Gadgets