anet a6 3d model

One of these linear bearing replaces two LM8UU bearings for the Anet A6 or Anet A8 bed. It is intended to primarily remove noise, mechanical play and weight. It is made of only two parts: a housing and a snap in spiral bushing. Self threaded M4 holes...

The update corrects the issue that on a standard Anet A6, the hot nozzle or fan nozzle can strike the drag chain on the original design. The gap for the bed spring has also been widened slightly to accommodate washers and similar components. Use the...

After trying various belt tensioners with mixed results, I decided to design a new one specifically tailored for the Anet A6 (or A8). This updated version is designed to be robust and securely fastened to a base table, as you can see in the...

The version I'm sharing is a modification to my original top spool holder design, specifically intended for newer Anet A6/A8 printers that are equipped with smaller spool rods. It addresses the common issue of the shorter threaded rod provided with...

If you want better prints and faster printing, you need to make the Anet A6/A8 more rigid with a stiffer frame. One way of doing this is to clamp or mount the y-carriage M8 rods to a solid base plate that can be made from plywood or similar material....

I really like the hot end light by bhamlin52 (https://www.thingiverse.com/thing:2721617) for the Anet A6, but it's annoyingly bright. I'm also a fan of dimmers, so I decided to add one to this light. I got the parts I used from AliExpress for less...

This is Remix of AM8 for Anet A6 or Alunar M506. You will need all hardware as prescribed in AM8 and assemble as instructed, but replace with these parts. The only difference is assembling Z motor mounts, which sit 4 mm above the bottom aluminum...

If you want better and faster printing, you need to make the Anet A6/A8 more rigid with a stiffer frame.One way of doing this, is to clamp/mount the y-carriage M8 rods to a solid base plate. The plate can be plywood or similar.</p><p>Most other...

A6 pendant

**02-11-2018** Anet recently changed the default A6 power supply at the start of 2018. The STL has been revised to accommodate the change, and still functions for pre-2018 printers. (i.e., some internal features were removed, and the screw hole over...

Trying to install an auto level sensor on my Anet A6.\nI managed to install it on the right-hand side from the front, but it blocked the X-axis going all the way to 220mm. This is another attempt - this time installing from the front using the fan...

This model is an adapter from the place under the Anet 1.0 Board to the SKR board For build i use 4 screws M2*10 and 16 screws M3*20 Used fan 50*50*15 I advise you to print from plastics with good interlayer adhesion. I used PETG Sources are...

... ...Its snug fit ensures the belt remains securely in place without any movement, while still allowing for easy removal when necessary. The design is versatile and adaptable to other printer models, provided the belt measures 6mm wide and 1.4mm thick.

I borrowed inspiration for this cover design from tobbi007's creation, which was a remake of the original Anet controller cover with added fan mountings and a hole. I had it fitted to my A6 after noticing that the heatsinks on the control board were...

I drew inspiration for this cover design from tobbi007's work, a reproduction of the original Anet controller cover with added fan mountings and a hole. I mounted it on my A6 after noticing that the heatsinks on the control board were heating up...

The ANET A6 printer's first layer is important to get accuracy landing. With this Fine Z level adjuster for the micro switch you can get this accurate with the ability to adjust the micro-switch level so that it lands and lays down the first layer...

The main challenge lies in mounting the sensor (gearbest.com/3d-printer-parts/pp_591321.html) without restricting X-axis movement, which is currently limited to 0-200mm. To overcome this limitation, I need to relocate the sensor to a different area...

The bolt and nut attach to the filament guide onto the holder, all using standard M3 nuts, which I believe the original A6 has plenty of extras. I've been excited to print this model but my rods are currently bent, so I'm unable to level my glass...

A hot bed remix to calibrate your Anet. ...8 x M3 screws

A Custom Enclosure for the Anet Motherboard Features Two MOSFETs and an Integrated Raspberry Pi 3 Module.

... exhibit some warping due to its small size and long shape - still, it works as intended. Print Settings Printer: Anet A8 Prusa I3 Rafts: Not necessary Supports: Unnecessary Infill: 10% Design Process SketchUp This model was created using SketchUp.

Задачей вентилятора является обдув и охлаждение электроники блока питания при длительной печати.The fan mounting model is 80x80x25 in size with a hole pitch of 71.5 to the power supply. The task of the fan is to blow and cool the electronics of the...

Hey guys, I've got a spool core here that's compatible with your Anycubic i3 mega or Anet A8 or Anet A6. It'll work with all three models. ...The diameter is 57.2 mm and it stands at 70 mm tall, so make sure the center hole of your spool fits snugly in...

Although the E10 and A6 connectors are quite similar in shape, the print didn't fit properly, so I chose to cut one piece off. Next, I upgraded the design but haven't had a chance to test it yet. ...Since the bed temperature isn't an issue when printing...

I wanted a new fan duct for my A6-mod, and the tiny one from Dovanzeijl's thing was making way too much noise. So, I made a new one using Tinkercad. Enjoy! ... Last updates: Screwless mounting at hotend fan Finishing clip at blower fan Round cutoff at...

I needed an angled tube to serve as a reliable filament guide for my Anet printer, and I created it using the versatile design software TinkerCAD.

Version B is specifically tailored to fit standard Anet 8mm nuts, whereas version A is optimized for stainless steel nuts that tend to be slightly smaller in size. A notable design feature is the incorporation of captive nuts, allowing for...

... be no version for the Anet belt of this type because it is recommended to acquire a better belt first before purchasing an H-frame replacement. You will require: 2x M3 nut (spare from Anet) 2x M3 screw (M3x30 spare from Anet) Enjoy your project!

The SD Card Holder for the Anet A3/A5 is mounted on the vertical frame directly above the motherboard. ...Its purpose is to secure firmly in place using a threaded hole that provides stability and prevents movement.

I adapted the jbanion design concept to create a tighter fit that securely bolts onto the z-stepper motor. ...To achieve this, I also designed a compatible version specifically tailored for the Anet A8.