anet a6 filament holder 3d models

Printer Support for Filament on the Anet A6 Printer

I push out Smartfil Flex at a speed of 120 millimeters per second, rotating the axis by 240 degrees, with no heat bed.

Motor Mount for Plates: Check out this design on Thingiverse: https://www.thingiverse.com/thing:2364937 This mount doesn't include a thread (M6) for the Teflon tube fitting, so you'll need to screw it tightly into the 5mm plastic hole. ... It's...

The project centers around creating a filament holder that seamlessly integrates with the existing ANET A8 filament holder. This innovative design draws inspiration from TUSH The Ultimate Spool Holder at https://www.thingiverse.com/thing:2047554,...

... holes. ...Additionally, you can now utilize standard 20mm screws to secure the holder onto the frame. Enhanced Mainboard and Dual Mosfet Holder for Anet A6. ...When assembling, use screws with a length of 20mm and 10mm for the boards respectively.

Now it can be used two ways: - Place it on top of the printer (ANET A6). - Use the top cut to hold a roll of filament. - Attach it to the IKEA shelf (2.4 cm thick) without screws, glue, or adhesive tape. - Use the side cut if placed horizontally...

... having to physically touch the hotend, minimizing the risk of damage or injury. The ANET A8 Plus Filament Holder is built with high-quality materials that ensure durability and longevity, making it an essential addition to your 3D printing setup.

I designed a filament roll holder for my Anet A3. ...Calculating the inner diameter of the spool yielded 50.8mm, so I created a component with a diameter of 50mm.

... fit, so printing it at 98% may be essential to ensure a smooth fit. To complete the assembly, obtain the screw and plate directly from Photograaf16, who originally designed this upgrade for Anet A6/A8 machines, specifically the Y-Belt tensioner.

Dimensions: 190mm x 180mm x 12mm If you have an Anet A8, be sure to check out my other mods: Anet A8 Z-axis Bar Wobble Stopper - https://www.thingiverse.com/thing:2800104 Anet A8 Power Switch Box - https://www.thingiverse.com/thing:2784564 Anet A8...

I designed this Anet Filament holder with a diameter of 54mm and a center hole measuring exactly 8mm in size. It perfectly fits the official filament used by Anet's 3D printers, specifically the A8 model. Print Settings: Printer: The chosen printer...

Anet a6 fun duct

Anet_A6_Z-endstop

After considering modifications, I designed a holder specifically for the Anet A6 printer. To assemble it, you'll need both the original and a mirrored version of this design. In my case, these two versions worked perfectly without any additional...

This roller is crafted to fit snugly into the stock filament holder that comes standard with Anet printers. Its overall length measures 120mm, and its outside diameter is a precise 35mm. Designed to accommodate 608 bearings (8mm x 22mm x 7mm in size,...

Fan duct for the original anet a6 x-carriage. Check compability with your endstop. ...This is a remix from this design: https://www.thingiverse.com/thing:4242375/files

... Fits an Anet A6 or A8 Printer or Other Printers with a 220x220mm Holder. There Are Two Different Versions Available: One with a 1mm Thickness and Another with a 3mm Thickness. Special Thanks to FedeMiller for Providing the Various File Formats.

If you already have an Anet filament holder, you can use some of those parts and save filament. Put everything together and secure it with the screws from the old filament holder. If you don't have screws and nuts, you can use superglue instead. I...

The version I'm sharing is a modification to my original top spool holder design, specifically intended for newer Anet A6/A8 printers that are equipped with smaller spool rods. It addresses the common issue of the shorter threaded rod provided with...

The filament flows directly from the top into the extruder, eliminating kinks that can occur with traditional spool holders. ... Required parts: 2 M3 x 30mm countersunk screws 2 M3 nuts (Both components were conveniently included as spare parts in my...

... as suggested by Dennjo83. Additionally, with a reel holder similar to ChiefSwiftNick's design, the reel rotates evenly. To prevent the filament holder from slipping off, I built an extra holder, which is visible in the picture and painted white.

I purchased two MOSFETs for my Anet A6 and initially planned to mount both above the mainboard, but Leo_N's design convinced me to install the hotbed MOSFET below the board using his horizontal version and the hot-end MOSFET above the board using his...

I don't have much space around the printer, so I installed the Anet remote spool holder which puts the filament at a bit of a distance and an awkward angle to the drive mechanism.\r\n\r\nThis handy mount allows the feed server to sit neatly under the...

... These spacers ensure optimal alignment of the bracket's mounting points with the existing holes on the Anet A6. ...The bracket securely fastens to three strategic points on the frame of the Anet A6, providing a solid base for reliable operation.

As I envisioned improvements, I decided to adapt the design for my Anet A6 by creating a holder that pairs perfectly with the original and a mirrored version. To ensure seamless integration, both versions work without any support required. ...If you're...

I've outfitted my Anet A6 with a versatile shaft holder that accommodates a diameter of 19.8 mm, essentially transforming it into a CNC machine. To utilize this feature, I'm running the Marlin firmware. For optimal performance, I adjust the...

I reinforced the base with sturdy extensions that enable seamless attachment to the Anet A6's upper surface, effectively creating a stable and secure anchor point for effortless setup and deployment.

In addition to the basic spool holder, two fittings are included to facilitate smooth filament rotation on the bar by minimizing friction. The hole that accommodates the bar runs uninterrupted through its length, allowing for potential extension in...

Dimensions: - External: 52 millimeters - Internal (screw): 8 millimeters If you: - Don't want to waste too much filament holding a spool - Are still using the original Anet "screw" that holds the spool - Use filament with internal spool dimensions of...

Fan duct for the original anet a6 x-carriage. ...Check compability with your endstop.</p> <p>This is a remix from this design:<br/> <a href="https://www.thingiverse.com/thing:4242375/files">https://www.thingiverse.com/thing:4242375/files</a></p>