anet a6 upgrade extruder 3d models

Upgrading the A8's motor and top plate on the Z axis requires mounting aluminum parts with a 17mm gap between the rod and screw, replacing the original 22mm setting. Motor plates can be found at https://a360.co/2LVloqT and top plates at...

Human: Upgrade of Previous Version (http://www.thingiverse.com/thing:1205037) Improved with Following Key Enhancements: Step Down Gear Ratio Increased from 1:1 to 2:1 for Z Stepper, Delivering 2x Torque to Compensate for Reduced Motor Power Enhanced...

To upgrade the size of the heating bed, two holes must be drilled. For expansion, you will need: 1 aluminium plate with a thickness of 0.4mm and dimensions of 310mm by 260mm 1 aluminium plate with a thickness of 0.4mm and dimensions of 260mm by 30mm...

_______________________________________________________________________ Good luck and let me know any problems or potential upgrades! I will be modifying it over time! If your feeling generous, a little support is always appreciated! I am a...

This is version 2 of a bearing/bushing housing which converts the Anet A8 stock y-carriage to a 3-bearing type. Three points must always align on the same plane. Version 2 addresses an issue that my y-carriage was upside down. Yours might be too if...

Want to put a face on your print head? :D I've created two versions: one with holes and one without, depending on the type of googly eyes you have available. Personally, I prefer plastic googly eyes used in toys. The ones I used are 14.8mm in...

This design was inspired by valpap's work and it served me well except for one crucial issue: de-rectractions with flexible filament. The filament somehow managed to break free from the intended path through the groove in the bearing, resulting in a...

I made this ectrusor because I was having problems printing on tpu, I have been using it and it has some failures, it can be improved but at least it can be printed, not like the one that comes from the factory

... the problem (available from amazon). But the air opening of the fan has different measures, the old ducts do not fit. Here is a duct for the Titan fan for the Anet A6. ...It takes into account that the nozzle is not centric to the fan outlet.

Anet ET4 Direct Extruder Upgrade Using Titan Edition Hardware.

You can buy it here for example: https://es.aliexpress.com/store/product/Freeshipping-1Pcs-Anet-3D-printer-Part-controller-RAMPS-1-4-LCD-12864-control-panel-blue-screen/1081732_32674974140.html Base for Graphic LCD (Official Anet A6) LCD12864 This is...

COVER FOR ANET EXTRUDER

Another step of upgrade of the BLV MGN12 Anet A6 A8 Full Metal Head Quick Connector: https://www.thingiverse.com/thing:4697481 It allows use of the Kossel Tackle:...

Dual part cooling system now integrated on the X-axis. ...Secure all components using Anet A6-approved hardware, specifically M3 machine screws.

The Power Supply MeanWell NES-350-12/RSP-320-12's mounting bracket will not fit on the Anet A6. ...Fortunately, however!

Key Features ========== - Reuse of Original Springs and Screws - Keeps Springs in Place from the Bottom and Top - Holds Firmly Glass on the Hotbed - Makes It Easier to Level the Plate - Corners Are Level or Lower Than the Glass Plate So the Extruder...

I've been using these for a few days on my ANET A6. ...With the bearing holders from https://www.thingiverse.com/thing:2640562, all printed on an ANET A6 with a 0.4 mm nozzle, everything seems to work just fine.

With this adapter, the plastic extuder on the direct drive upgrade, can be replaced with an metal extruder from creality.

Here is a longer version of the original "Anet A6 LCD, Raspberry Pi Zero W and Camera Housing.stl" Its' on both sites 14 mm longer (between the outer holes)

Here is a longer version of the original "Anet A6 LCD, Raspberry Pi Zero W and Camera Housing.stl" Its' on both sites 14 mm longer (between the outer holes)

I reengineered Orseeny J's Anet A8 Dual Extruder mount for Bowden to accommodate a third extruder. ...This modification is particularly useful for upgrading to diamond hotends.

Upgrade my printer to direct extruder from China.Based version DIY 3D Printer "Metall Bot". ...Самодельный 3Д принтер H-Bot " Metall Bot"

I revamped it to integrate seamlessly with the aluminum extruder upgrade, allowing me to maintain full functionality of my cable chain system.

Upgrade my printer to direct extruder from China.Based version DIY 3D Printer "Metall Bot". ...Самодельный 3Д принтер H-Bot " Metall Bot"

Ender 3 upgrade for the extruder. Works with flexible filament. ...Use a M4 Bolt and nuts to span the spring if needed.

The modified Replicator 2X extruder upgrade replaces the printed bearing axle with an M4 flat head screw. To implement, keep the base part from the original design while printing the arm and cover pieces from this Thing. ...This upgrade ensures a more...

I've been using the Craftbot-plus and Craftbot-2 printers, but their directdrive extruder design really needs improvement.\r\n\r\nThat's why I'm testing Bart's Hotend Upgrade first. ...After some time, I decided to upgrade my Craftbot with a real Titan...

... and pushing the screws through to offset the motor slightly before tightening the screws holding it in place. All screws and bolts used were items I had on hand after upgrading the extruder, some of which originated from assembling my Ender 3.

This upgrade, termed as Replicator 2 Extruder Wire Bundle Strain Relief Upgrade (R2EWBSRU), simplifies the extruder wire management for MakerBot Replicator 2 users. To install it, print R2EWBSRU (in about 6 minutes). Next, slip the extruder control...

Optimized Upgrade Solution for Printrbot Metal Plus Low Profile E3D Extruder Upgrade your Printrbot Metal Plus to experience unparalleled performance and precision with the low profile E3D extruder. This cutting-edge solution offers a seamless...