anet a6 upgrades 3d models

Trying to install an auto level sensor on my Anet A6.\nI managed to install it on the right-hand side from the front, but it blocked the X-axis going all the way to 220mm. This is another attempt - this time installing from the front using the fan...

I borrowed inspiration for this cover design from tobbi007's creation, which was a remake of the original Anet controller cover with added fan mountings and a hole. I had it fitted to my A6 after noticing that the heatsinks on the control board were...

The ANET A6 printer's first layer is important to get accuracy landing. With this Fine Z level adjuster for the micro switch you can get this accurate with the ability to adjust the micro-switch level so that it lands and lays down the first layer...

I drew inspiration for this cover design from tobbi007's work, a reproduction of the original Anet controller cover with added fan mountings and a hole. I mounted it on my A6 after noticing that the heatsinks on the control board were heating up...

This upgrade, or any extensioner upgrade, together with a y-tensioner upgrade and toothed idler pulley (in both x and y) are three of the most critical upgrades to your Anet 3D printer. You will see an improvement in print quality once you get the...

I'm attaching an action camera like a GoPro to my Anet 3D printer.

A hot bed remix to calibrate your Anet. ...8 x M3 screws

It enables the use of a 12864 LCD screen, available on Amazon through this link, to upgrade to Marlin 2.0 without dealing with touchscreen firmware issues. https://www.amazon.com/gp/product/B078Y647LT/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1...

First of all, a huge thanks to Dovanzeijl for the [Anet A6 x-carriage](https://www.thingiverse.com/thing:2171816). This model is heavily based on his original work. # The Problem Calibrating my [tronxy based...

A Custom Enclosure for the Anet Motherboard Features Two MOSFETs and an Integrated Raspberry Pi 3 Module.

This is an upgraded version of my extremely simple yet highly efficient adapter for filament spools designed specifically for the spool holder that came with my Anet A8. The old version can be seen at http://www.thingiverse.com/thing:1950461. It will...

One of these linear bearing replaces two LM8UU bearings for the Anet A6 or Anet A8 bed. It is intended to primarily remove noise, mechanical play and weight. It is made of only two parts: a housing and a snap in spiral bushing. Self threaded M4 holes...

I wanted a new fan duct for my A6-mod, and the tiny one from Dovanzeijl's thing was making way too much noise. So, I made a new one using Tinkercad. Enjoy! ... Last updates: Screwless mounting at hotend fan Finishing clip at blower fan Round cutoff at...

The human element plays a crucial role in adjusting the end stop on an A6 or A8 3D printer, and the gear knob is the primary tool for making these precise adjustments. ...By turning this knob, users can fine-tune the distance between the print bed and...

I needed an angled tube to serve as a reliable filament guide for my Anet printer, and I created it using the versatile design software TinkerCAD.

... be no version for the Anet belt of this type because it is recommended to acquire a better belt first before purchasing an H-frame replacement. You will require: 2x M3 nut (spare from Anet) 2x M3 screw (M3x30 spare from Anet) Enjoy your project!

I've uploaded two different patterns: one with hex cutouts similar to my other parts for the A6, and another with circular cutouts for a more classical look in sync with the power supply. Variants include models with and without screw holes for the...

I adapted the jbanion design concept to create a tighter fit that securely bolts onto the z-stepper motor. ...To achieve this, I also designed a compatible version specifically tailored for the Anet A8.

The SD Card Holder for the Anet A3/A5 is mounted on the vertical frame directly above the motherboard. ...Its purpose is to secure firmly in place using a threaded hole that provides stability and prevents movement.

Here's a fun quick print, a hanger for the micro SD to USB adapter that came with the A6. I designed it so you can leave it on the adapter at all times (so its a wee bit tight) and still be able to plug in the USB. It takes ~15 minutes to print. I'm...

This is a supplement for the A6 hotbed Y axis belt parallel issue. It fixes the bad belt geometry that causes the Y axis to rebound. To fix this problem, you will need 4 M3 x 30mm screws and 4 nuts. Place the nuts on a strip of tape, making it easy...

... problem. Notice in pictures I have installed crystal corners that compress springs 1mm aprox and centers in the opposite side that compress another mm else. Whit this Z end stop springs are in similar compression than A6 original design. ...

This model is an adapter from the place under the Anet 1.0 Board to the SKR board For build i use 4 screws M2*10 and 16 screws M3*20 Used fan 50*50*15 I advise you to print from plastics with good interlayer adhesion. I used PETG Sources are...

Counterweight to compensate for the difference in mass on both sides of the X-axis in the Prusa/Anet BLV MGN12 mod: https://www.thingiverse.com/thing:2567757 The weight is Madcat BB Swivel Lead 300g:...

I attach this lighting bar to my Anet mods, which is a simple LED strip for the bottom frame under the LCD display. I install a 12V LED strip featuring 5050 SMD's to produce optimal light output. It plugs directly into my power supply. ...This helps...

I designed a sleek and understated belt holder for the Anet A8 that achieves the perfect balance between stability and accessibility. Its snug fit ensures the belt remains securely in place without any movement, while still allowing for easy removal...

One is a revised Jadames Cross Beam, featuring a filament guide attached to it - a reworked design from dlddesign, specifically tailored for the Anet A8. ... I've also included an attachment version of this beam in case you already have it printed,...

... screws) to attach the plate with tensioners. A suitable axle is M3 x30 along with corresponding nuts. I use original Anet bearings. Warning! The axle that holds the bearing must not be fully tightened. ...The bearing must be able to rotate freely.

I'm designing a hybrid fan duct and auto levelling sensor mount for the A6 printer. The main challenge lies in mounting the sensor (gearbest.com/3d-printer-parts/pp_591321.html) without restricting X-axis movement, which is currently limited to...

Print Settings for Stock A6:\nNozzle Set at 0.4\nInfill Set at 20% Cubic\nCircular Fill for Top and Bottom\nTravel Speed Set at 40 mm/s\nMiddle Part Requires Support, Separated for Printing.\nCustomized Version of Thingiverse's #2037492\nCreated with...