anet a8 acrylic frame 3d models

User installs a single support for fixing one motherboard, specifically the Anet A8 original with two MOSFETs measuring 60x50. ...The user utilizes the existing holes in the frame for securing the support.

This bracket was designed to mount an Anet A8 3D printer down to a wooden surface with screws. ... Bracket goes over the left and right all-thread frame rails.

This adapter lets you attach a LCD 2004 display, like the one used on RAMPS 1.4, directly to the Anet A8's standard frame. ...The protective covering is also included.

I'd love to adjust my heated bed adjustment screws on my Anet A8. ...The butterfly nuts will make the lower holes in the frame look nicer when I add some supports.

This is a Wyze V3 mount that clips on to the Anet A8 frame on either side of the Anet LCD display. It slides in and out easily. ... The camera slides onto one side and the other side clips onto the frame.

BOM: 2 * Allen key M3 x 18 for far right screws 2 * Allen key M3 x 20 for replacing existing 2 * Allen key M3 x 30 for mounting to vertical part Few washers Print Settings: Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.25 Infill: 25% Notes:...

PROS: - Little expensive and full compatible with the Anet A8 - In certain cases reduction of the vibrations - Improvement of the stability of the heating bed - Possibility of precise regulation of the squareness - Possibility of installing a deeper...

This is a reworked version of the Leo Hulk frame bracing design, tailored to fit the A8 5mm wooden frame edition. The sole modification made was to thicken the bottom frame support. ...As it stands, this frame brace significantly enhances frame...

White Tara clip to attach to the top frame of your Anet A8. Probably would work better as two separate pieces... less supports. This will probably be updated in the near future... Print Settings Printer Brand: Anet Printer: A8Rafts: No Supports: ...

Included are separately logo'd models for the Anet A8 and the Anet A8 Plus printers. ... I've seen similar designs on Thingiverse, but I wanted to match the Anet logo's I've put elsewhere on my Anet printers, while keeping any potential air flow...

To achieve tight smooth rods, which standard Anet A8 frames often fail to provide due to large tolerance for rod holes, I remixed this design by removing the bearing holder. ... To install z-couplers correctly: Visit...

======== Before: Y-axis rework for Anet A8 by matsekberg After: Enhanced Y-axis rework for Anet A8 by matsekberg, expertly combined with Anet A8 Y Axis Rework by viktor3d Is this upgrade truly necessary? ... Provided 2 distinct hole sizes, 6mm and 8mm...

... a M8 mount on top that allows for seamless integration with a threaded rod. Be sure to finish the M8 nut holder with a side cutter after printing. Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 4%

This support integrates the OVM20 Lite 3d printer's electronic board case with the Anet A8 frame. https://www.thingiverse.com/thing:2482835 The OVM20 Lite is an all-in-one electronic board from staticboards, combining Arduino, Ramps, and DRV...

This is a custom-built camera mount for the ANET A8 3D printer or any other printer with a matching clamp width on its frame. The platform disc has limited clearance, so you may need some force to securely fit the Playstation Eye Camera into it. Once...

This is a scaled-down version of butchja's Universal Filament Spool Holder main hub, resized to fit the acrylic spool holder included with the Anet A8. Visit https://www.thingiverse.com/thing:2070272 to get the matching threaded nut, as well as...

###well here's the story with this.### I wanted to use the L3K extruder with my A8, but the Bowden Remix uploaded is made for 2020 (as well as 2040) frames, so what's a guy to do if all he has an A8 with the stock acrylic frame? I had three choices:...

Other designs for the Anet A8 can be found below: Check out my remix of Leo's rear frame brace at http://www.thingiverse.com/thing:2246689 Visit my front frame brace at https://www.thingiverse.com/thing:2224643 See my Anet A8 Y Axis Belt Tensioner...

I created a custom card extender case specifically for my Anet A8, but it can also work with other 8mm frames. I deliberately designed it to blend in seamlessly with the frame's design, without any protrusions or obstructions. ...This sleek case...

Specifically, this change impacts acrylic-framed printers with a five-button configuration located next to the LCD screen. You can find more information about these printers at the online store aliexpress.com, specifically under seller number...

Industrial-Grade Mounting Solution - Anet A8 Pillar Washer, M3 x 7 Thread Designed Specifically for Securing the LCD Display on Your Anet A8 3D Printer.

Защитный кейс с кнопкой "Reset" для материнской платы принтера Anet A8.==============================================================Protective case with "Reset" button for Anet A8 printer motherboard.

Anet A8 80mm Fan Cover\nA protective cover for the electronics of the Anet A8 designed to accommodate an 80mm fan

How I Designed This I designed this thing specially for my Anet A8 PRUSA i3 with an acrylic 8mm frame, which came to me without a recognizable belt connector in the box. After some time with an improvised setup, I created one that does the job a lot...

... ... *** Summary *** The acrylic plate that comes with the Anet A8 auto bed leveling kitkit broke in half when I tried to screw it on. The holes are also in a bad spot. The inductive sensor would get hit, and prevent the Y-endstop from being reached.

Summary The acrylic plate that comes with the Anet A8 auto bed leveling kit broke in half when I tried to screw it on. The holes are also in a bad spot, which causes the inductive sensor to get hit and prevents the Y-endstop from being reached. The...

*Update 7/15/2017* Made cutout larger so homing Y min works without hitting. *Summary* The acrylic plate that comes with the Anet A8 auto bed leveling kitkit broke in half when I tried to screw it on. The holes are also in a bad spot. The inductive...

Simply print the mirror pair and push in the bearings and mount on the acrylic frame of the A8 using the existing bolt holes and smooth track (red circles). Longer bolts will be required, but I found extras supplied with the kit that worked just...

Curved guide which snaps onto the acrylic top frame of the Anet A8 to help the X cable slide over freely. My X carriage cable kept sticking when going over the edge of the frame, so I made this guide to help it pull over more smoothly. I was getting...

Curved guide which snaps onto the acrylic top frame of the Anet A8 to help the X cable slide over freely. My X carriage cable kept sticking when going over the edge of the frame, so I made this guide to help it pull over more smoothly. I was getting...