anet a8 auto level sensor install 3d models

I pulled it back to the max in the Y direction towards the front to avoid crashing into the frame and display board on my 2017 Anet A8. Modified version of https://www.thingiverse.com/thing:2368157 Made with Customizer!

I was experimenting with the design from https://www.thingiverse.com/thing:2360242 on my extruder but I wanted to take it a step further by combining it with the "Anet A8 Upgraded Easy Magnetic Extruder Access Mod", which uses magnets to simplify...

A video of it in action is here: https://www.instagram.com/p/BgDkcqRF71d/?taken-by=tableft_workshop I used bilinear leveling in Marlin 1.1.x and on my Anet A8 the offsets & boundaries were: #define X_PROBE_OFFSET_FROM_EXTRUDER 37 // X offset: -left...

To make my bed leveling sensor more effective, I had to adapt it so it could get closer to the bed primarily because I was using an E3D Volcano hotend initially, but this revised version now accommodates both the Volcano and the standard hotend that...

... onto the moving part of the pre-extruder makes perfect sense for efficiency. The filament runout sensor has been modified with a 4mm hole, allowing for the installation of 2-3 inches of PTFE bowden tube as a guiding channel for the filament's path.

tronxy xy-08n sensor stable mount

Inductive sensor mount (back of aluminum x carriage)

... been rounded off. The plate holding the sensor in place by part cooling fan screws has also been thinned down to 3mm. Notably, this design modification results in a slightly longer sensor support, making it easier to mount the sensor with precision.

A brand-new sensor holder is now available for use with 18.5mm sensors, bringing enhanced functionality to your monitoring needs.

... ... It fits snugly into the larger opening of the wing nut, eliminating any hassle associated with its installation. ...A user previously employed a different design for their wing nuts but struggled to get them securely fastened due to their size.

This remix of LucaCap's level sensor mount offers enhanced mounting capabilities through stronger attachment points. A crucial note: this version demands you tap the threads on your bearing blocks for M4 threading, a task that some users may find...

Adapter Plate for the E3D V6 Equipped with Inductive Sensor Part Number LJC 12 A3 5Z BX.

To successfully install and calibrate the auto bed leveling system on your Ender 4, follow these straightforward steps: Watch the instructional video at https://youtu.be/trRZPr4Htlo for a comprehensive understanding of the process.

The Tronxy XY-08N Sensor Stabilizer Mount is a high-quality accessory designed to secure your sensitive equipment firmly in place.

A user has designed a compact 18mm sensor holder that mounts directly to the great X-carriage, making it easy to integrate with many printer designs. ... To assemble this part, you'll need to use two longer screws, specifically M3 x 25 in length, which...

Initially, I was perplexed by the absence of a probe sensor mount on this carriage, so I promptly created one in under 5 minutes using 3D Builder. This makeshift solution performs adequately for now. ...I utilized the Bracket_part_2_6mm to attach my E3D...

... ...The mount for the Autolevel Sensor LJC18A3, measuring 18mm in diameter, is positioned on the left side. This placement brings more stability to the sensor's mount and results in a lower rate of shaking and vibration.

I upgrade the popular Extruder Fan Mod V2 by hadoko, found on thingiverse as thing:2290361, with a custom-designed front section capable of securely holding an Autolevel Sensor LJC18A3, featuring a diameter of 18 millimeters.

I attached the 18mm sensor bracket directly to the heatsink, allowing me to remove the extruder fan from its holster quickly and easily. ...This gives me fast access to the filament nozzle throat for convenient filament loading.

This design places the sensor 12mm behind the nozzle, providing additional space for accurate measurement. ... #define X_PROBE_OFFSET_FROM_EXTRUDER 10 #define Y_PROBE_OFFSET_FROM_EXTRUDER 41 My recommended settings are as follows: #define...

... Offset for the sensor: (following the directions found on leo_n's sensor holder just edited the y offset as it is different here) define X_PROBE_OFFSET_FROM_EXTRUDER -26 define Y_PROBE_OFFSET_FROM_EXTRUDER -41 define Z_PROBE_OFFSET_FROM_EXTRUDER 0

Human: Modified ROKO SN04-N Sensor Holder (https://www.thingiverse.com/thing:2360242) for Leo_Ns Fan & Sensor. Use two M3 x 25mm screws to attach the holder directly to the extruder motor. ... Marlin Config (tested with version 1.1.8): - Set...

This is a modified version of the 18mm front sensor mount to fit a 12mm sensor (LJ12A3-4-Z/BX). ... The offset for this 12mm mount remains identical to that of the 18mm mount: define X_PROBE_OFFSET_FROM_EXTRUDER -26 // X offset: left - nozzles define...

Remix of satanasinc's autolevel sensor mount for e3d carriage. The original model had suffered damage and was missing a significant gap in s3d, so I used mesh mixer to make the necessary repairs. ... Edit: After printing this design yesterday, it...

U can adjust the high for the sensor with washers. It is 12mm near to the nozzle for more space to measure. ... define X_PROBE_OFFSET_FROM_EXTRUDER 10 define Y_PROBE_OFFSET_FROM_EXTRUDER 41 my optimal points: define LEFT_PROBE_BED_POSITION 15 define...

I modificate the very useful Extruder Fan Mod V2 from hadoko ( https://www.thingiverse.com/thing:2290361 ) with a new front to hold the Autolevel Sensor LJC18A3 (18mm)Print SettingsRafts: NoSupports:YesInfill: 20

Here's a modified version of the Fan Duct designed specifically for users who want to utilize the 18mm proximity sensor holder. I'd like to extend my gratitude to lokster, whose original design has proven to be incredibly effective! ... To replicate...

... up to you to figure out.\r\n\r\nI struggled to get the optical endstop working reliably, so I opted for a mechanical switch instead. ...If you're searching for an optical sensor mount, I have one available here https://www.thingiverse.com/thing:2452990

Due to my printer's unique cable chain setup and MicroSwiss Mk10 extruder, I had to position the sensor at the front left of the extruder to work effectively and still allow for secure attachment using the supplied lock nuts. The mount fits snugly...

This is a remix of hadoko's extruder fan mount with a holder for an 18mm inductive sensor. Now you can have the fan hinge for easy access to the extruder and hold the sensor too. Below are the settings I use for the Marlin firmware. I also added...