anet a8 bed size 3d models
583217 3d models found related to anet a8 bed size.thingiverse
for upgrade the size of heating bed. its need to drill 2 holes its. for expansion you need: 1 aluminium plate 0.4mm thickness 310mmx260mm 1 aluminium plate 0.4mm thickness 260mmx30mm 2 aluminium plates 0.4mm thickness 310mmx55mm 2 printet parts 2...
thingiverse
Supported linear systems - SBR12 - MGN12 (H & C) - LM8UU blocks - V-Slot wheel 2020 extrusion profile - V-Slot wheel 2040 extrusion profile Supported bed sizes and hole spacings - 220mm x 220mm (Anet A8) - 300mm x 300mm (Anet A8 plus) - 310mm x...
thingiverse
Attachments to the wing nuts on the Anet A8 bed It is slitty bigger than the wing nut so it will fit in with ease, I printed someone else design but had problems getting the wing nuts in place.
thingiverse
Needed a new bed for my Anet A8+ couldn't find a original one The closest in size I found was the Cr-10 bed on Amazon wich is 310x310 and uses the same resistors and thermistor. The only issue i had was that the holes of the normal bed frame didn't...
thingiverse
Petit clip de 6mm de haut pour maintenir un glasse (3mm) sur votre plateau chauffant d'une anet a8
thingiverse
i was sick of adjusting the print bed with the stock system using springs. so i made these 15mm spacers that replace the stock leveling springs. ...just tighten the screws firmly and you should be good to go!
thingiverse
I purchased some high temperature spray paint in blue and black and set printing my design on the glass with PLA after the print was finished I sprayed the bed black with PLA still attached after 2 even coats I left it to dry. Then removed the PLA...
thingiverse
Two versions of Anet A8 bed leveling knobs. ...You can use stock Anet A8 bolts or M3 bolts.
cults3d
Lighting bed Anet A8 printer. Valid for others models. ... Materials: GU10 cap GU10 LED lamp, 220V
thingiverse
Remix of AlbEagle's great Anet A8 Bed leveling knob (https://www.thingiverse.com/thing:2807594) - thanks AlbEagle! I removed bottom to make the wingnut touch the heated bed. It is no longer possible to use M3 nuts. ... You can use stock Anet A8 bolts...
thingiverse
Lighting bed Anet A8 printer. ...Valid for others models. Materials: GU10 cap GU10 LED lamp, 220V Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 1,75
thingiverse
Anet A8 Chain Bed Protector Remix 200 nozzle - 40 bed - 80% infill - 0.2mm height Remixed from : Xibel Edited by : KoekMaker98
thingiverse
Anet A8 hot bed upgrade ... ...in order to avoid a deformation of the belt because the distance of the frame and the actuator is too high
thingiverse
I designed this to support the cable of the Anycubic Ultrabase heatbed fitted on my Anet A8. Printed in PLA, 0.2mm, support with the bed only. ... Enjoy !
thingiverse
My cable from the bed was scraping off the acrylic frame of the Anet A8 so I designed an guide for the cables.
cults3d
I designed this to support the cable of the Anycubic Ultrabase heatbed fitted on my Anet A8. Printed in PLA, 0.2mm, support with the bed only. ...Enjoy !
thingiverse
Just Y carriage for anet A8/A6... it is lighter and inelastic compared to the original. print from ABS or ABS+, 4 shell and 35% infill. do not use springs when mounting the bed! use only teflon washer! ...
thingiverse
Anet A8 thumb adjusters and spring bushes for bed level adjustment. Remove bed and drill out 3mm carriage threads with 3.5mm drill Fit original screw through heat bed with washer and 3mm nut. slide over spring and spring bush fit through...
myminifactory
these clamps are intended for use with 20x21x3mm glass beds on anet a8 (or more in general any bed smaller than the anet aluminium hotbed). the aim was to definitely remove the paperclips avoiding noozle collision as much as possible, allow glass...
thingiverse
... the photo you can see, in the front right corner it is too far away, and in the front left too near. Print this, adjust your bed screws and then print again. Feel free to donate a buck if it helped you :) Get your Anet A8 here: (click on the image)
thingiverse
... settings in my slicer. If you have a printer with a larger or smaller build plate, then I'm sure you can just scale this model in your slicer to fit the size of your bed. Just make sure it is centered in the slicer before you go to print. ...
thingiverse
Bed leveling spring holder for Anet A8. Print 8 pieces together. (2 for each spring) Specs: Internal diameter: 8.5 mm Hole diameter: 3.5 mm Wall thickness: 1 mm Floor height: 1 mm Total height: 60 mm This thing was made with Tinkercad.
thingiverse
Anet A8 bed leveling knob with opening for M3x3 brass insert. Use a soldering iron to heat and melt the insert into the part. ...M3x3mm Brass Insert: https://www.amazon.com/gp/product/B015A31MBW/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 Print...
thingiverse
This is a remix of an existing bed setting device for ANET A8 printer. I design this parts because the original buttons enter in contact with the frame of my printer (diameter to big). I also design new spring guide with nut shape. With my design...