anet a8 belt upgrade 3d models

This section is intended for installation on the X-axis drive of the Anet A8-M 3D printer.

Print Settings Printer: Anet A8 Rafts: No rafts are needed for this print. Supports: This model does not require any supports. Resolution: The resolution of the print is set at 0.3 mm. Infill: The infill density is set at 100%. Filament:...

I measured them on my ANet A8 and they fit quite well. The front part is placed around the original brackets for the y-belt tension, while the back part is positioned via the holding part of the stepper motor. They are not designed to withstand...

I combined the self-locking mechanism from a Y axis belt holder with an X axis belt holder for the Anet A8. I drew inspiration from two existing designs: https://www.thingiverse.com/thing:2489277 and https://www.thingiverse.com/thing:2264558. The...

Yet another X-belt tensioner for the Anet A8 catches my eye, but this one has a twist. It boasts an ultra-low profile design, allowing you to mount it snugly inside an IKEA Lack enclosure. It requires only two M3 machine screws and two m3 nuts, as...

So, after six broken idlers, I decided to create this part that uses standard ANET A8 // A8 ball bearings (used for belts) and an idler without a bearing. You can remove both ball bearings using an M3 screw and a hammer, along with an M8 bolt for...

... cover to be undersized. To resolve this problem, I lengthened them in the model. Everything now works flawlessly and has already withstood several prints on the Anet A8. ...Note: I'm still uncertain whether it will continue working on the Prusa I3.

I crafted this specifically for the Anet A8 and similar models. ...This part accommodates an idler pulley with a maximum of 20 teeth.

You'll need to tighten the Y-belt tensioner on your Anet A8 wooden frame to ensure smooth operation and prevent damage. To do this, locate the tensioner which is usually situated near the extruder motor. It's a small pulley with a bolt in its...

This is a V3(Sub v2) remix of toosha's anet A8 Y belt tensioner - remix v2. Sub v2 as toosha had already remixed it to a V3. This adds the bottom 2 support pieces that was mentioned in the comments for V2 - seemed like a good idea, so I edited it...

ANET A8 BELT TENSIONER and BRACE Y-Axis We have thoroughly installed and tested the components. Every part fits together seamlessly. The M5 nut trap is incredibly tight. Position the nuts in front of the traps, then use the 30mm screw to draw them...

I designed this Anet A8 Y Axis Belt tensioner for GT2 Aluminum Pulleys. You will need a 5mm metal plug that fits directly into the 5.2mm hole, still tight enough, and inside the pulley. Check out example links below. You can buy the metal plug at...

I began to rebuild my Anet A8 printer, starting with the X belt holder and tensioner. To assemble this crucial component, I needed one M5x50mm bolt, one M5 lock nut, and a spring with an outer diameter of less than 8mm and an inner diameter of more...

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.80 Infill: 100% Notes: You probably don't need 100% infill, but this small part has a lot of tension on it. It took about two hours to print at these settings. A higher...

(2017/2018 version). Use the original belt - no new purchase required. The tensile forces of the belt no longer affect the right-hand suspension of the X-axis. This eliminates distortion on the vertical threaded rod of the z-axle. Note that grub...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

Rear Anet A8 X Belt with BL Touch Holder - a remix based on creations by zumili and matsondawson. The probe is positioned at the rear for a cleaner look, utilizing one M3 nylon nut as spacers. Several configurations need to be modified to make this...

This is an edit of the Anet A8 X-belt Toothed Idler Tensioner by butchja. I rounded off the edges for a better appearance and thinned out the supports - unfortunately, I was unable to get the original ones into their hole. (This part is the green...

I needed a tensioner for the x-belt on my Anet A8. I couldn't find one that would fit the idler I bought, which is larger than the regular one and has a 5mm wide shaft, so I decided to make a new tensioner inspired by several similar existing...

I fabricated the Anet A8 improved X-belt tensioner by freemark and required some customization to suit my needs, as I wanted to utilize a toothed pulley rather than the standard one.\r\nAdditionally, I sensed a size disparity between the nut and the...

Anet A8 AM8 X belt Tensioner GT2 Pulley 16 teeth: The Key to Perfect Step Performance For flawless step execution, the GT2 Pulley 16 teeth with a bore of 3mm is essential. This precision-crafted component ensures seamless motion and optimal...

Reworking of the Thingiverse model 1666094 was undertaken to achieve a superior fit with the lower linear bearing on the X-axis carriage of my Anet A8 printer, which the original design struggled to accommodate effectively.

As most of you are aware, the Anet lacks a genuine ability to adjust belt tension in the y-direction, and the belt does not run parallel between the stepper and pulley. Some solutions have already been implemented regarding tension adjustment or...

My goal was to achieve a similar design aesthetic while addressing two key issues: the narrower gap between the belt and the idler, as well as providing enough space for a genuine toothed idler pulley instead of the standard flanged bearings supplied...

After trying various belt tensioners with mixed results, I decided to design a new one specifically tailored for the Anet A6 (or A8). This updated version is designed to be robust and securely fastened to a base table, as you can see in the...

One lower version was printed using PLA with a 0.25mm resolution on an Anet A8 B, achieving a precise fit. Due to its higher rigidity, PLA is recommended for this project. UPDATE: Initially, Version 1 was designed for a 50mm x 4mm profile based on...

... by Olon, a seasoned expert. ... Crafted specifically for the standard Anet A8 Y carriage, this innovative tool requires only two M3 screws and matching nuts to secure it in place. ... Designed to seamlessly integrate with the renowned Tatara frame.

It is part of a series of upgrades I made on my Anet A8 and that I will post all projects here soon. It is very simple to print, spends very little filament and is extremely tight so it does not cause vibrations and most importantly you will not...

It is part of a series of upgrades I made on my Anet A8 and that I will post all projects here soon. It is very simple to print, spends very little filament and is extremely tight so it does not cause vibrations and most importantly you will not...