anet a8 filament guide 3d models

Anet A8 simple filament guide. ... Helps align and hold the filament as it enters the extruder.

I have made a few improvements to the original [Anet A8 Filament Guide](https://www.thingiverse.com/thing:1795148). This part was made for the new Anet A8 and I have no clue if it will work on the old one. Here are the changes: * Scaling has been...

I have made a few improvements to the original Anet A8 Filament Guide. This part was made for the new Anet A8 and I have no clue if it will work on the old one. Here are the changes:Scaling has been fixed, so you no longer need to enter weird values...

Filament guide for the Anet A8

A simple filament guide for the Anet A8 3D printer.

Filament Guide for Anet A8 Printer, you can put both horizontal and vertical. ...Enjoy

Simple filament guide for Anet A8 printer; Stops filament from dragging on the extruder inlet and chafing. ...Print Settings Printer: Anet A8 Rafts: Yes Supports: Yes How I Designed This Designed in Blender 2.76b

Very simple filament guide for Anet A8. Mount it on the display frame using one of the screws. ...Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2

This helps to guide the Filament to the extruder of the Anet A8. Simply place it on top and run the filament through. ...The Walls are shaped conical to allow a tight fit.

fits Anet A8 frame

... will not move around during printing. Printing instructions: - PLA material - print this upside-down - print with infill of 25% - print with a Raft and Support - print time approx 45 min I hope you enjoy using this filament guide for the ANET A8.

Simple Filament Guide for the Anet A8 Printer. Added 2 versions for short screws. V1 lower screw holes (1.5mm) V2 rear wall only 1.5mm thick. Please test ! ...Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 25%...

I have my spool of filament sitting on the side of my printer, so this guide uses the screws that hold the frame together to mount on the front of my Anet A8 printer.

This filament guide is only usable without modifications if your bobine is at the right to your printer and only if your printer is an Anet A8 Don't use support in the hole because of the shape of it.

Filament guide for Anet A8 printer, that mounts at the side of the screen. Choose the left or right side mount. ...It prints without support, but needs cooling (even if printing in ABS) and slow speed.

Filament Ring to Anet A8. ...Printed 0.2mm and 35mm/s

This is a remix the Anet A8 Prusa i3 Simple filament guide by papinist. https://www.thingiverse.com/thing:1764285 I have my spool behind my printer and found with the original design it was rubbing on the front of the printer. I have added a...

Filament guide on Anet A8 with pulley for easy movement. I choose PLA because of good bridge creating on one part. To assembly you need just one M3 screw and nut. If you liked it, please let me like. ...Thank you.

Another Filament guide for Anet A8. I rounded all the edges for better filament movement. And I put a slot in the top so if I forget to thread it through first, I can engage it later. Print this 'upside-down' as shown. The stringing should be fine.

... to peal off. Optionaly, it hold a filament filter: http://www.thingiverse.com/thing:497764 (ps. excuse my bad English, it's not my native language) Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 100%

A simple filament guide for the Anet A8. Both open and closed versions included, try them both and use whichever works best for you! They fit snugly on the top of the Acrylic frame (7.5mm) with an 8mm gap. ... The model may need rotating - prints best...

A simple filament guide for the Anet A8. Both open and closed versions included, try them both and use whichever works best for you! They fit snugly on the top of the Acrylic frame (7.5mm) with an 8mm gap. ... The model may need rotating - prints best...

Print Settings Printer: Anet A8 Rafts: Yes Supports: Doesn't Matter Resolution: .1 or .2 Infill: 25 Notes: For this particular print I stood the print on end with the filament guide on top like the star on a Christmas tree and used a raft on the...

This is my version of a filament guide, as used on my Anet A8. The mount slot is a shaped fit for an 8mm thick panel. The modelling will ensure an easy fit and a good grip on the panel. The split front on the piece will allow filament to be slotted...

For my set up I use it in combination with these 2 links:http://www.thingiverse.com/thing:1624641 andhttp://www.thingiverse.com/thing:1975954 Print Settings Printer: Anet A8 Resolution: .1mm Infill: 25 Notes: I printed with supports. 200 degrees...

https://www.thingiverse.com/thing:2502487 This is a filament guide for the Anet A8. Intended for a spool positioned behind the printer.<br/> I didn't want to put my spool holder on top of the printer, so I kept it behind the printer and designed...

This is a guide for your filament so the filament doesn't get stuck or something. ...It is a perfectly fit on the top on the net a8- frame

Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: .2 Infill: 50% Notes: I used supports for the base Post-Printing Assembly The mating areas on the guide's bottom piece and the base will need to be cleaned up a little before gluing....

This is a simple, clip on/slide on, filament guide that I made for my Anet A8. it'll fit on anything that is 8mm thick. It clips/slides on the top part, right between the screen and the buttons. What's different about this one is that it's...

I designed this filament guide to use the original screws that mount the LCD to the A8 printer(yes they are long enough). When I added the X-axis chain to the printer the filament would catch the chain and would allow the spool to tangle. There are...