anet a8 hotbed wiring 3d models
94937 3d models found related to anet a8 hotbed wiring.
thingiverse
Remix of Anet A8 Hotbed Cable Holder by song7070 The changes I made are the distance between the two aluminium plates, this is now 12.2mm. The space between the lips is 3.4mm. ... I also added extra holes so the cable can be fixed with two ty-wraps...
thingiverse
Made a plug for my Anet A8 hotbed because mine got burned like in picture above. ...
thingiverse
This is a Protection for the hotbed of the Anet A8 or other printers with the Anet A8 hotbed. The springs sometimes caused issues and damaged the hotbeds bottom layer. There have been cases were the hotbed even sparked and caught fire! This fixes the...
thingiverse
Ein Kabelhalter, für die Kabel am Heatbed bein Anet A8. ...Entlastet den Stecker und verhindert das dieser durch die Zugbelastung während des Drucks herausgezogen wird.
thingiverse
This make is for a bracket for mounting a camera to the hotbed of Anet A8 printers. The bracket affixes to the top of the H-bracket, below the actual hotbed. We re-use the holes for the linear bearings and an end clamp to attach the mount to the...
thingiverse
After printing the hotbed stain relief support I really liked the way it was attached to the hotbed and since I was making a short version I though why not just add a handle to the end instead and this is the result. ... The STL is for a single...
thingiverse
Here it is useful and cosy thumbwheel for adjusting hotbed easily and fast. i found really nice this project https://www.thingiverse.com/thing:2350276 but I noticed wheels where too hard to tight. Upgrading this way are now easily to screw. ...Suggested...
thingiverse
Please check out my new product The "OFFi" Auto-off switch for ANET A8 at: http://www.ebay.com/sch/i.html?_nkw=jimb15122 Print Settings Printer: ANET A8 Rafts: Doesn't Matter Supports: No Resolution: .3 or better Infill: any Notes: Mounts firmly in 3...
thingiverse
For Anet A8, printed on Anet A8 @ 0.2mm. ... work on 7mm total thikness (3mm hotbed + 4mm glass).
thingiverse
You can find it at the hardware store for about 5 eur, the sheet is about 70x100 cm and you need a square of about 22x22 cm; some kapton tape glue (every type should work) tools (scissors and cutter) Check out all my Anet A8 projects: Anet A8 Prusa...
thingiverse
... like a little bit unstable. So I made cable holder. It can makes more stable your Anet A8's hotbed cable. 1. You need only a small zip tie. 2. There is no interference with hotbed. (Glass, Pad) 3. Easy to print. ...(No supports, Short time)
thingiverse
UPDATE 18/08/217: New spacer uploaded, now you can use a glass of 3mm of thickness up of the hotbed. Spacer for fixing Anet A8 hotbed. As you can see in the second picture, with this spacers hotbed will be completely leveled from the corners. ...
myminifactory
You can find it at the hardware store for about 5 eur, the sheet is about 70x100 cm and you need a square of about 22x22 cm;some kapton tapeglue (every type should work)tools (scissors and cutter) Check out all my Anet A8 projects: Anet A8 Prusa i3...
myminifactory
A simple spring bushing for the Anet A8 hotbed springs to prevent warping and bending of the springs. By using the OpenSCAD file it can be adjusted so it should be pretty generic. The screw is a tight fit but I find that a good thing for it's...
thingiverse
... idea it is my own version of a piece i saw once. this fits a heat bed for the Anet A8 220mm x 220mm heat bed after the plug is removed and wires soldered directly to board. ...please go easy on me for the design and the lack of information on it.
thingiverse
... sideways so it will be easier when I decide for some enclosure. You can see all my notes, recomendations and mods for Anet A8 here: https://www.mikrom.cz/3d-tiskarna-anet-a8/ (it is in Czech, but I am sure you know how to use Google Translator)
thingiverse
### Contenido: ### + **holder_hotbed:** * es la pieza completa, separa la cama caliente y H y sujeta el cristal.* + **separador_hotbed:** *es la pieza que separa cama de H, sustituye al muelle.* + **holder cristal:** *es la pieza que sujeta el...
thingiverse
After seeing lots of people having problems with the hotbed connection shorting out over time, and not being able to find anything apart from cable chains that more often than not required turning the bed sideways and soldering wires directly to the...
thingiverse
A simple replacement for the adjusting nuts that come with the printer. ...Threads in hotbed frame must be removed by drilling. These thumbscrews make levelling much faster and easier. ...No screwdriver will be needed after the installation.
thingiverse
Anet A8 Centralized Wiring Enclosure?? UPDATE: FINISH AND TESTED This is a project I've been working with for a little while now. I thought I'd post some images in hopes others might share some ideas and/or improvements before I finish and post...
thingiverse
after a short cut with original wiring and connector on my heat bed, I have decided to design this mounting. It is glued on bed support with epoxy and by clamping the harness before bed , there is no more movement and then no more damage on...
thingiverse
This is a hotbed, insulation, and glass holder for Anet A8. It uses standard Anet screws and springs. It takes a 4mm thick glass, 3mm insulation and a standard 3mm Anet 220x220mm hotbed. There are two files. One is a 1/4 piece wich should be printed...
thingiverse
... two corners for best results use 4 corners (4x corner file included). For best results, print in ABS. Will also work in PLA if using a low temperature. Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100%
thingiverse
Strain Relief for the hotbed cable from the A8. ... Attaches only to two screws of the "H" bed holder.