anet a8 lack enclosure 3d models

Recently purchased an Anet A8 Plus for a budget-friendly Cartesian setup, which arrived in semi-assembled condition with one of the bed bearing holders cracked. To remedy this situation, I designed and printed a replacement part to ensure seamless...

This is another MicroSD extension holder for Anet A8. I made it because all of the holders I saw were made to attach them on the upper side of the printer. Other holders needed screws that just added extra hassle. I have a cabin, so it's impossible...

I plan to integrate the RPi with the display on top of my Anet A8 printer's right corner. The base plate will attach directly to the existing right corner plate, and the arcs and holding brackets can be clipped into place. ...I'll need to verify if...

This Anet A8 Handle was designed to make it easy for users to move the Heatbed along the Y-Axis. The handle makes it possible to avoid unnecessary burns and levelling procedures by eliminating any unnecessary tension on the heatbed levellers. The...

I recently had a fire erupt in one of my Anet A8 printers while it was printing with ABS, triggering the smoke detector and prompting me to take action. To prevent such incidents from happening again, I inserted a .25Amp fuse in line with the fan and...

... To fix this issue, I print two of these clips and attach them to the second and third links in the chain. After that, I simply relax and let the printer do its thing. Here are my print settings: Printer: Anet A8 Rafts: No Supports: No Infill: 100%

On the ANET A8, the front and rear mounts feature machined tolerances so massive that the Y rods float freely with at least 1/10th mm of play. This excessive movement is a primary cause of X wobbling, noise, and vibrations. To correct this issue, a...

This induction sensor is designed specifically for the Anet A8 3D printer. The mount cleverly utilizes the screws from the extruder fan, allowing for a seamless installation process. All you need to do is print it out and secure it in place, making...

I wanted to install a Filament sensor on my Anet A8's X carriage, so I designed a bracket to hold it securely in place, ensuring the filament route lines up perfectly: https://www.thingiverse.com/thing:2443425 In addition to its original purpose, I'm...

This is a custom filament guide for the Anet A8 printer. It helps bridge the filament over the left shoulder of the printer to prevent contact with the acrylic frame. One side flexes slightly to reduce tension during movements along the x-axis,...

I designed a precise gauge holder for the Anet A8's bed leveler, which fits perfectly on the x-axis rods. Its accuracy is confirmed by consistent measurements every time you remove and reattach it. Unlike other holders I found on Thingiverse, this...

Two versions of the Z-Stop (mechanical) Holder for the Anet A8 - one standard size, combining two parts, and another slightly wider\r\n\r\n\r\n\r\nAppreciate My Designs? ...- Help Me Out by Buying a Coffee!</strong></h1>\r\n\r\n<a...

Easy Upgrade for Stock Anet A8 Filament Spool Holder. Dangling Spool on Bare Threaded Rod Was a Problem. Solved with Simple Modification Using M8 Nut Knob - A Crucial Upgrade for Smooth Operation. Threaded Rods Are Essential, But They Don't...

After several printouts on my Anet A8, I noticed that the Z-rod started to develop a small amount of vertical play. Upon disassembling and reassembling the frame, I discovered that something had shifted inside it, and this approach wouldn't resolve...

I designed this spool holder specifically for my ANET A8, a top-notch 3D printer. ## Minimalist yet robust design I'm not one to waste filament on printing unnecessary components, so I took it upon myself to create my own optimized spool holder...

Body1 is a custom designed remake of the original holder for Anet A8 x-belt tensioner, specifically tailored to my printer. The part calls "gabel" and "gabel_pulley" are actually idler components, while the knob is sourced from an existing project....

The advantages of this design include: * Reduced material usage * Faster printing time * No gap exists between the fan housing and the cover My other designs for the Anet A8 include: * A case for the PowerPanel-LCD:...

This allows the anet a8 X axis endstop to be shifted by 15mm. I designed this because after I printed [this](https://www.thingiverse.com/thing:2435075) very good BLTouch holder the carriage wasn't able to reach the sensor (It reached the acrylic...

... to a 3D print project, I appreciate your understanding and feedback. This design is a remix of Anet A8 - Power Supply Cover with Switch by Puddlefist, originally published on June 16, 2017, and available at www.thingiverse.com/thing:2320216.

A simple PS Eye mount for the Anet A8 and other printers with the same stepper motors. Mounts on either Z-axis motor for v1 and v2. v2.5 and up only mount on right side. Use original hardware*(a little close right now so i will add holes for the...

Guys and gals, this is the complete linear chain for Anet A8 print. Some parts like right linear chain or linear chain part are NOT designed for me. My designs. End left part of the chain (green). Support of the right part (green). Be free to share...

... The updated v2 has a larger 11mm opening to accommodate a 9mm teethed idler pulley wheel. These are the ones I used: http://www.ebay.com/itm/301834183849 Print Settings: Printer: Anet A8 Rafts: None Supports: None Resolution: 0.2 mm Infill: 25%

Printer Settings: Printer: Anet A8 Rafts: No rafts are required. Supports: Supports are not necessary for this print job. Resolution: The resolution is set to 0.1mm for optimal detail. ... Infill: This print will have no infill, resulting in a hollow...

Modified the Anet A8 Led Ring Holder by bigvlad to use the extruder fan mounting screws for easier access. This modification eliminates the need to disassemble the print head in order to mount this bracket. The bracket takes a 100mm led ring,...

this is my definitive cooling fan duct for anet a8.very simple easy to print, it looks like the stock one but it is larger and it has the fan connector integrated.print as found in the STL without supportsYou can find all my models here, thank you...

The Anet A8 X belt tensioner boasts a sleek design, featuring a single thumb screw adjustment that keeps it low-profile and avoids collisions with the extruder carriage. This innovative design cleverly utilizes spare screws and nuts provided with...

The text discusses a storage solution for a 3D printer, specifically an Anet A8. The current frame is made of acrylic but will be replaced with an aluminum profile frame in the near future. The building process is ongoing and expected to be completed...

I required an expedient bowden mount for my Anet A8 after acquiring my titan extruder and wishing to abandon the direct drive configuration. I modified the NEMA 17 motor mount and appended a few "v" shapes on the bottom of the mount (they will be...

I designed a revised version of an existing bed setting device for ANET A8 printers, as the original buttons kept coming into contact with the printer's frame due to their large diameter. To solve this issue, I created new parts featuring a...

Add a script for each layer of your print in your slicing software: G90 ; M108 8000 ; G0 E-10 ; G1 Y200 ; G1 X-33 ; This script is for anet A8, it will move the bed always in the same spot, then the X axis will home to click on the earbuds. ... ...