anet a8 m 3d models
146381 3d models found related to anet a8 m.thingiverse
I searched for days looking for the firmware for my anet a8 m and the newer board that was on it, finally found it so i thought i would share. There may be some bugs in the firmware but at least it will get you started. I got my auto level working...
thingiverse
Because the Anet A8-M has dual extruders, it is not possbile to use the regular fan ducts that are created for the regular Anet A8. So I decided to make one ;) This fan duct is inspired by lokster's "Spriya" fan duct found here:...
thingiverse
A small but irritating problem on the Anet A8-M is the fact that the screen support plate rests on the screen connectors once tightened. This is causing both the display circuit board and the support plate to bend. Due to this bending the rotating...
thingiverse
Customized version of https://www.thingiverse.com/thing:2204941 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2204941
thingiverse
For now, just the version for the right hand extruder. Should be easy enough to mirror though. Unfortunately I edited the none 'fixed' version, so it appears to have some structure inside the body which can cause slicing issues for some software. ...
thingiverse
This mainboard-cover fits on a KFB-2.0-Mainboard, which comes for example with the Anet A8-M (dual extrusion). Feel free to use it. ...I´m using a 40x40x10 fan on it.
thingiverse
replacement part for Anet A8 (prusa i3) or Hesine m-505 X axis belt mount Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: Layer height - 0.1mm, nozzle - 0.4mm, speed 60mm/s. Use brim. ... ...
thingiverse
Spool Holder for the Hesine M 505, Anet A8 Spool Mounting Setup Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20 %
thingiverse
Extruder Fixation Plate for PTFE Tubes or Bowden Extruder, etc. ...Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20 - 100 %
thingiverse
My printer used to "wobble" around during printing so i decided to add some fixation plates in the corner which helped well. ...Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100%
thingiverse
Spool Holder "Holders" for fixation via screws. ...For the Hesine M 505 Spool holder. Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100%
thingiverse
Filter for PTFE Tubes and Wall mounting. ...To use with an interior piece of sponge Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 100%
thingiverse
... people liked my design :) On several requests i added a V2 version with a lesser angle on the back for better printing. ...Have fun printing! Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100 %
thingiverse
A simple holder for Logitech C270 Camera. ...The two wings are for better adhesion on glass. After print you can simple remove this. Print Settings Printer: Anet A8 Prusa i3 aka OMNI 3D printer Rafts: No Supports: No Resolution: 0.2 Infill: 25%
thingiverse
There is no fixing for Z-axis shaft in Hesine Prusa i3 M-505 This small thing will fix this issue :) Print Settings Printer: Hesine Prusa i3 M-505 Rafts: No Supports: No Resolution: 0.2 Infill: 100%
thingiverse
Even shorted M505 cooling nozzle remix. My extruder nozzle is screwed close to the tension gear and pulley. ... I needed to remove 2mm so this cooling nozzle would not touch the bed.
thingiverse
I've mounted my extruder head up-close so the pipe almost touches the feed mechanism. There is only one screw length of pipe sticking out so I needed an even shortened M505 cooling nozzle. ... I think this is the shorter you can get because a shorter...
thingiverse
Just test printed this and works fine for me. Its a bit short, because the original was bumping and scraping on the print and movin it. ...Shoutout to the original creator : Arjjck.
thingiverse
It is for bowden. If you have other size of spool hole (height and orgglass width) or want to change angle use customizer or edit openscad file directly. ...Customizer is buggy and shows angle wrong (full 360 degrees)
thingiverse
Upgrade of the popular fan blowing with resizing and adding vertical height adjustment https://www.thingiverse.com/thing:1620630 I centering it by the geometric center of the hothead because air flow is stronger at the base of the ring. New...
thingiverse
The original can be found here: https://www.thingiverse.com/thing:2899752 Fits both the Anet A8 and Anet A8-M perfectly and this is perfect if you have the filament mounted on top of the printer and like to keep the filament in place and not going...
thingiverse
Users have reported this design also works on the Anet A8 and other printers. This mount is easily installed behind the blower fan. (You may need longer screws) For firmware, I'm using Marlin RC-8. I've uploaded a .zip of the firmware currently...