anet a8 plus power supply 3d models

Improvements for Anet A8 Plus Z Axis That Will Use Standard Motor Supports of the Printer and Standard Axis Position. This modification helps reduce axis wobble and motor position offset in relation to the 20x40 T-slot profile. I recommend using...

My Anet A8 Plus kit was vibrating and shaking on the z axis when printing. While searching for a solution, I came across @3Displacement 's Prusa Bear X Upgrade which instantly caught my mind. After a few test prints, things where improved but I...

My Anet A8 Plus kit was vibrating and shaking on the z-axis when printing, which made me desperate for a solution. While searching online, I stumbled upon @3Displacement's Prusa Bear X Upgrade, which caught my attention immediately. After conducting...

I took matters into my own hands as I couldn't find any A8 Plus versions available, so I created them myself. The original designs are there too, but they came out in a lower quality print. I opted for 70% infill due to stability concerns when you...

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

As part of my ongoing upgrade of my A8 Plus, this is a clamp for the X-axis belt on the carriage. ...This replaces the stock (rather poor) part with a solid one and removes the tensioning facility in favour of an external tensioner (which I've already...

I didn't find anything for the A8 Plus Version, so i did them by myself. The original ones are printed too, but in a lesser Quality. I printed with 70% Infill because of stability reasons, when you really want to tighten the screws. I will upload...

I designed these mounts to be uncomplicated and allow the boards to dissipate heat instead of being confined in an enclosure.\r\n\r\nSmoothers...

I had an ATX power supply running my A8 until recently, but I finally traced bed-heating problems back to an overloaded ATX12V output that had started going bad. I replaced it with a powerful 750W HP server power supply equipped with a PCIe breakout...

I wanted to swap out the Z-axis bearings on my A8 plus with minimal fuss. This is a straightforward device that lets you push the old bearing out of its seat by its replacements. I opted for two pairs of IGUS LM8UU bearings, which I swapped in...

I've upgraded my Anet A8 to use an E3D V6 and Titan extruder, giving it a significant boost in performance. The upgrade process was straightforward, with the only hurdle being finding a suitable mount for the Titan extruder. I finally stumbled upon...

I designed this support for my Anet A8+ to reduce bouncing at higher speeds. It attaches directly to the extruder fan and one of the carriage bearing brackets. To assemble it, you'll need longer M4 bolts (15mm) for the bearing bracket and possibly...

All bracketry is new and applicable to the Anet A8 Plus. Features Include: 1. Lightened and miniaturised chain links, 1.4g vs 2.4g for the old style commonly found. 2. Cable installation on the fly - cut out channel on links and brackets for...

For all A8 Plus Users who are not satisfied with the belt attachment on the bed, just like me! Remove the screws, insert the belt in the clamp, then attach it back to the bed. Don't forget that the other side of the belt also needs to go through the...

As part of my ongoing upgrade of my A8 Plus, this clamp is designed for the X-axis belt on the carriage, replacing the stock (rather poor) part with a solid one and eliminating the tensioning facility in favor of an external tensioner, which I've...

I discovered numerous squash ball feet on Thingiverse suitable for the A8 Plus, although none were specifically designed for it. These can be bolted directly into place of the stock feet without altering the original chassis height. I measured a 6db...

A sturdy mount to locate your Sovol 6 Plus power supply outside your 3D printer enclosure. Power supply can easily be accessed or removed after mounting by sliding it out the top. You need 4 screws to attach to the wall. ... Print with no...

I've remade a 120mm fan mount for the Anet A6's power supply, trimming unnecessary parts to speed up production and conserve filament. ...I've also relocated the fan upwards, as that's where my PSU tends to get hottest.

Designing a Support for Power Switch Convenience, Since Anet A8 Lacks a Comfortable Shutdown Option

... Link to instructions on how to hook it up to the original A8+ Board: https://h2lab.org/fablab/a8_bltouch/ (Not, mine, all credit goes to them.) Link to SKR 1.4 upgrade kit: https://www.thingiverse.com/thing:4761697 (Mine, all credit goes to me :)

I'm excited about completing the build of my Anet A3+ and tackling upgrades that will take its performance to the next level. To start, I've identified a crucial enhancement that caught my attention - a device designed to provide strain relief for...

... version. The power supply width is approximately 110mm. ... For the intended switch, I opted for the Hifi Lab Einbau Stecker, available on Amazon at https://www.amazon.de/Hifi-Lab-Einbau-Stecker-Einbau-Buchse-Kaltger%C3%A4te-Buchse/dp/B01FQVM9EM.

Marlin 2.0.x The switch is linked to the LCD display via PIN 29 and GND, similar to Anet A6. ... I utilized this limit switch: https://www.aliexpress.com/item/32889409224.html?spm=a2g0s.9042311.0.0.2ad64c4dT8dphg Configuration.h: #define...

Bolt Needed: Four M3 screws, each half a meter long and twenty-six millimeters thick, plus two washers. Two M3 screws, each half a meter long and nine millimeters thick. ... One M3 screw, half a meter long and fifty-one millimeters thick, attached to a...

... ... 12 Volt led strips come equipped with an adapter, which can be purchased on Aliexpress at the following link: https://bit.ly/2NyUZ04 5 Volt led strips are powered by usb and also available on Aliexpress at the following link: https://bit.ly/2NyDnBL

I began designing a cable holder for wires originating from the second z-motor and two power wires, which eventually became a functional piece. This modification does not replace the motor bracket. In my opinion, it's better to retain the metal...

... Microswitch KW12-3 itself. Its compact dimensions - 20x10x6mm (Lxbxh) - belie its impressive capabilities. This miniature marvel is a testament to modern engineering's ability to pack immense power and reliability into an incredibly small package.

The power supply might not need as much cooling, but I wanted a big fan there anyway! To attach it, you'll need three M3 screws that are 18mm long. Print Settings: Printer: Anet A6 Rafts: Doesn't matter what they are. Supports: Yes, they're...

A case for the original Anet A6's power supply to include a switch with a fuse and a power meter. The original idea of MartinS79. The holes for the screws are not included; I prefer to machine them. *Switch:*...

Installing this simple power supply cover will significantly enhance the safety of your 3D printer operations. To assemble you'll need: * Two M4 6mm countersink screws * Two M4 nuts * One M3 6-12mm countersink screw * A socket with a fuse and...