anet a8 plus power supply 3d models

A custom cover for the Anet A8's stock PSU is now in place, expertly crafted to accommodate a powerful 120mm fan and a sophisticated controller that effortlessly turns the fan on and off with precision. The fan of choice is the impressive 12CM Miner...

Model created by: ME Printer used: ANET A8 PLUS @anet3dprinter Slicing software: Cura 3.2.1 Layer height set to: 0.2mm Printing speed set at: 60mm/s Bed temperature maintained at: 80°C Printing time took approximately: ~45min Filament used: ANET ABS...

This wire strain relief is designed specifically for the Anet A8 Plus hotend, and it necessitates using 2mm longer M4 screws to function properly. ...It should be compatible with standard zipties.

Remix of the "Anet A8 Plus Fan Duct" from Celil Türkmen Modified the attachment (expanded by .1mm on each side) to attach better to the extruder mount Original file here : https://www.thingiverse.com/thing:3749653

This modification adapts the original design from https://www.thingiverse.com/thing:3570293 to accommodate the Anet A8 Plus. ...The switch holder has been adjusted downward to ensure a secure fit on this specific 3D printer model.

I upgraded the ANET A8 PLUS Extruder Fan component today. I made significant changes to the extruder assembly. ...By replacing the cumbersome bolt with an accessible design, I greatly improved the overall user experience.

This is a remix tailored to the Anet A8 power supply fan shroud. To make use of an old computer's 120mm fan, I decided that a larger fan shroud was in order. The best part about this design is its customizability - I've included the SCAD file so...

... having to physically touch the hotend, minimizing the risk of damage or injury. The ANET A8 Plus Filament Holder is built with high-quality materials that ensure durability and longevity, making it an essential addition to your 3D printing setup.

I designed this fan mount due to heating issues with my Anet A8 Plus printer. ...The design requires no screws to secure the entire component to the extruder, relying instead on a sturdy M3 screw and nut assembly to hold the fan firmly in place.

... https://www.youtube.com/watch?v=6PL_rSPZ3M8 *You also have to set a X offset in the slicing software:* In Ultimaker Cura => Preferences -> Config. Cura -> Printers -> Anet A8 PLUS -> Machine Settings -> Extruder 1 -> Nozzel offset X := 34.0mm Enjoy!

Anet A8 3D printer modification. ...Add enclosure for incorporating switch and power cable into the power supply.

I believe a power supply that supplies 15A requires only a fan attached or built in, which is essentially a cover for an 80mm x 25mm PC fan.

Attach the Power Supply to the bracket with m3 cap screws, and then secure it to the 2040 rail with M4 Screws. The m3 cap screws will sit flush in the bracket. I used an m3 tap for screw holes on the second layer. You may be able to simply screw...

------------------------ Anet A8 plus 3D printer, in FreeCad format. Design created to facilitate the creation of new parts or modifications. It is done with the greatest precision possible. I am new to FreeCad so it is possible that the design...

The box described here attaches to the motherboard cover of the Anet-A8-Plus printer. It safely houses two Mosfet transistor cards for the nozzle and tray heating. A 12V fan can also be added, allowing a plastic cover to circulate air through the...

The A8 Plus has a poorly designed leveling knob known as Tihi.

Modified a standard power supply casing to accommodate a switch and an IEC connector at the rear, while also incorporating additional ventilation openings for improved airflow.

Remodeled the Creality hotend mounting system to seamlessly integrate with the Anet A8 Plus, while incorporating other modifications. This upgrade now enables users to utilize an unlimited supply of Hero Me's and Petsfang's. ...I highly recommend...

To attach the thread guide, first locate the four screws that hold the X-axis carriage in place on top of the Anet A8 Plus. Remove these screws using a screwdriver. Next, locate the two threaded holes at the top center of the printer's frame, one on...

I liked the Anet A8 Heatbed Camera Mount Logitech C920 by Catchy with the A8+ it was not long enough with a 300 x 300 bed. I extended it to make it work, This is my VERY First RE-Mix. ...

Recently purchased an Anet A8 Plus for a budget-friendly Cartesian setup, which arrived in semi-assembled condition with one of the bed bearing holders cracked. To remedy this situation, I designed and printed a replacement part to ensure seamless...

Das war nötig, da am ANET A8 Plus der Druckkopf um 45mm versetzt zum Rahmen ist und bei Druckkopfbewegungen im oberen Druckbauraum das Filament sonst zu stark anknickt am originalen Auslauf. Zudem kleine Designänderungen am Filasense und den...

This is a straightforward ATX PSU mount for the Anet A8 printer, situated on the right side. It may work with other models, but confirmation is uncertain. With this design, the PSU can be easily positioned and reused in the future without any screws...

Cover Design for Universal Power Supply Use, Featuring an Integrated Switch Interface: A Practical Solution for Easy Access - Specifically tailored for users who possess a power switch like my own IEC 320 C14 model, this cover design boasts the...

Human: Cabinet for Anet A8 Plus\r\nWhat you will need?\r\nMDF board or similar with 6mm thickness in the following measurements:\r\n2x 60 x 60 cm (Front and Back)\r\n2x 60 x 70 cm (Sides)\r\n2x 61.2 x 70cm (Floor and Lid)\r\n\r\nLeo Madeira, Leroy...

This remix is designed for a style power supply, switched plug socket, and USB charger: https://amzn.to/2KPgcQy (30A DC Universal Regulated Switching Power Supply 360W) https://amzn.to/2J4JeOF (Power Socket with Fuse and Switch) * Make sure you get...

Decided to craft my own custom power supply cover as most Anet power supply covers from 2017 didn't match the stock power supply that comes with today's batch of Anets.\r\n\r\nStill, there's a possibility this design may not fit your specific power...

This design can also serve as a standalone circuit board mount, allowing for attachment to a wall or other surface without the base or power supply. I included optional mounts for MOSFETs near the top of the enclosure. Wires will need extension, as...

This is my version of the many replacement fan ducts for the Anet A8 Plus. I tried a number of the others and found that they either didn't fit the fan properly (falling out too easily) or pointed in the wrong direction. This latter point is to be...

This is a solution for a single or pair of storage drawers which fit under the front of the Anet A8 plus. They provide an excellent place to store your snips, feeler gauges, allen keys etc. They include a sequence of clips to tidily and securely...