anet a8 plus y axis problem 3d models

This is a customized version created by MarNok, tailored to fit a 42mm watch case rather than the standard 50mm size.

I had a slight variation in my frame while using my previous design (thing:4716755), so I looked for a version that used the tapped holes in the frame, and this one matched perfectly! ... The only reason I remixed it was because I wanted a slight...

The Anet A8 features a unique Y-axis tensioner designed specifically for the GT2 20-tooth pulley, which incorporates an M5 bolt/nut assembly acting as the tension bolt in its second iteration.

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace is ment to extend your Anet A8 Plus in the X and Y directions by 40mm. The brace will help stabilize the frame and the added room gives you enough...

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace extends your Anet A8 Plus in the X and Y directions by 40mm, providing stability to the frame and sufficient space for a 330x330mm hot bed surface....

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace is ment to extend your Anet A8 Plus in the X and Y directions by 40mm. The brace will help stabilize the frame and the added room gives you enough...

Upgraded my Anet A8 with a modified Y-axis motor holder from thingiverse's 2045010, an outstanding improvement. My original holder warped due to excessive belt tension and overheating stepper motors, particularly after printing it in PLA. ...I...

I printed the previous Y-Axis tensioner (https://www.thingiverse.com/thing:2149867) but discovered that the belt section was too tight for my Anet A8 printer. I took the part and widened the section where the belt and pulley system are, giving it...

... in size, but it features a recess for the Y-axis belt and does an excellent job of securing it - without breaking easily. Print Settings: Printer Brand: RepRap Printer: Anet A8 Prusa i3 Rafts: Yes Supports: No Resolution: 0.1mm Infill: 80%

Many thanks to Simhopp for original design https://www.thingiverse.com/thing:1430727 Frame support with y-axis motor mount for Anet A8 (May 2017 edition) - http://www.gearbest.com/3d-printers-3d-printer-kits/pp_337314.html Mount the motor onto the...

... is finally here, and it's a game-changer. ...The new Y-axis Belt Bearings Support is incredibly simple to print, requiring the bare minimum of advanced settings. ...In fact, you can have this essential component up and running in just 20 minutes flat.

A reinforced clamping system for added stability on your Anet A6 or A8 3D printer, designed to secure the Y-axis and ensure a tight fit on the print bed. This clamp provides extra support for smoother prints and reduced warping. ...Simply attach it to...

Anet A8 Y-Axis Cable Chain v2: To secure the cable chain, simply close it using the small stick provided, or release it by removing the entire unit. The snap-in mechanism should now function more smoothly. ...(https://www.thingiverse.com/thing:1915486)

I don't receive any compensation if you buy one of these.* -------------------------------------- Other Designs from me for Anet A8 -------------------------------------- Check my remix of Leos rear frame brace:...

Anet A6 or A8 Frame Secure Clamp for Y axis For reinforcement for y axis and tighten on board Print Settings Printer: Anet A6 Evolution Cube Rafts: Doesn't MatterSupports: Yes Resolution: 0,3Infill: 20% Category: 3D Printer Parts

This Y-Axis Idler Pulley fits for wider idlers on your Anet A8 Frame Part, boasting an expanded gap of 0.4 mm over the standard Anet A8 piece.\r\nYou'll also need to secure a M3 rectangle nut in place, which will be a breeze due to its streamlined...

This little bracket keeps Y axis chain held down when the bed is at its back travel, preventing nozzle hits during starts and wide X moves. Not an elegant design, but gets the job done. Intended to be half a millimeter under Glass bed height;...

This is a remix that doesn't require a separate 8mm bolt, just print and install. ...This is one of the best Y-tensioners for the Anet A8

This is a set for the Anet A8 Y axis using my Lion Links from: https://www.thingiverse.com/thing:3179124 I encountered problems with my second printer and a standard Y chain from Thingiverse that kept getting stuck in the frame, causing print...

The better approach is to maintain three points to guide the plane plus an additional point utilizing the flexibility of the Y plate to absorb this hyperstatic mount. I then decided to design a parametric LM8UU based on a set of three standard ball...

The good idea is to keep 3 points to guide the plane plus 1 another one using the flexibility of the Y plate to absorb this hyperstatic mount. I then decided to design a parametric LM8UU based on a set of 3 standard ball bearings. Once installed...

Bolt necessary :\. ...Two M4 x 0.7 long 8mm bolts plus two nuts for aluminum frame are required. ...Nineteen-inch chain needed.

A small redesign of my original 12mm Y Rod holders, just chamfered all the top edges to help them blend in with any "Bear style" builds.

A small redesign of my original 12mm Y Rod holders, just chamfered all the top edges to help them blend in with any "Bear style" builds. ... Category: 3D Printer Parts

A small redesign of my original 12mm Y Rod holders, just chamfered all the top edges to help them blend in with any "Bear style" builds. ... Category: 3D Printer Parts

This is my take on the Anet A8 Y-Axis Cable Chain. The chain lies neatly to the right side of the heated bed, well out of the way of the extruder's home position. To get started, print 14 separate chain segments and rotate your heated bed a full 90...

The y-axis motor mount is a crucial component of the Anet A8 3D printer's frame structure, designed to securely hold the y-axis motors in place while allowing for smooth and precise movement along the y-axis. This essential part ensures that the...

Rear Support System Boosts Stability for Anet A3 Printers - Includes Essential Components Such as Y-Axis End Stop and Stepper Motor Mount.

Anet A8 Y-Axis Cable Chain Work&Force&Weight Optimized I obtained the components from "papinist" at Thingiverse (https://www.thingiverse.com/thing:1915486). Issues: Following the Printout - I discovered that the chain holder at the hotbed has...

This is a 2-piece Y-axis belt holder for the Anet A8! If you've upgraded your belts to fiberglass, check out my other items - I have one designed specifically for that upgrade, although this design works with both belt types. Make sure your H-frame...