anet a8 power supply 3d models

... on the print quality. All my Anet A8 designs can be found here: * Lightweight and unobtrusive X-axis cable chain for the Anet A8 * Slim and robust x-axis tensioner for the Anet A8 * Anet A8 power supply cover with LCD power meter and switch

I intentionally strengthened the right hand part, but if you press too hard, it may break anyway, depending on the quality of your print. All my Anet A8 designs: Anet A8 lightweight and unobtrusive X-axis cable chain Anet A8 slim and robust x-axis...

I'm remixing a power supply switch socket for my Anet A8. For all the connectors and switches, I took them from an old computer power supply. This is designed for the new version of the Anet A8, with a supply measuring 11cm in length. ...On the left...

I just bought an Anet A8 Plus, which has a similarly mounted power supply to the Ender 3, but then Anet does one better and has their power supply fan vent inward towards the build volume... I needed something to redirect air outside of the build...

PSU: http://amzn.eu/eMDl1Bh Switch: http://amzn.eu/cVd8COD Required hardware: - 2 x M4 10mm screws with nuts for switch installation - 3 x M4 10mm screws for stand assembly - 4 x M4 4mm screws for mounting the PSU to the stand - 4 x M3 10mm screws...

I created this custom power cover for myself and a friend because we couldn't find any compatible covers for our upgraded power supplies. Any tips or tricks would be greatly appreciated since I'm new to designing. The V2 version has screw holes that...

The Power Supply Enclosure Boasts a Honeycomb Design, Crafted by Hisham and Refined by Konmat1998. ...Additional Honeycombed Openings Have Been Added, Alongside Customized Access Points for Varied Switches and Sockets.

This specific setup positions the left edge of the power supply closely against the edge of the vertical support. If you're using a PS Cover, you'll need to adjust the position of the 150 x 50 holes slightly to the right. An included .obj file...

The original design didn't mesh well with power supply covers like this one: https://www.thingiverse.com/thing:2599267 - the left side screw would hit the frame. To fix this issue, I shifted the frame screw holes over by 5 millimeters, which clears...

I modified Puddlefist's cover to accommodate later A8 types, addressing a common issue where people struggled to get it to fit properly. To optimize material usage and reduce print time, I thinned out the outer shell, enabling prints in approximately...

A Rush Job Design for an Upgraded Anet A8 Power Supply (12V 30A) Using a Fused 110V Socket with Switch: Quick and Dirty. This design is perfect for those who want to upgrade their Anet A8 Power Supply without spending too much time or money. The...

this is Anet A8 honeycomb Power Supply cover with switch. Designed by Hisham. Just print it with the honeycomb facing the bottom. if you made one just give me like and tell me you made one Print Settings Printer: Anet A8 Rafts: No Supports: No...

I designed the Anet A8 Honeycomb Power Supply Cover with Switch, a clever accessory that adds functionality to your 3D printer. With a simple design, this cover is easy to print, requiring just one layer facing downwards on your honeycomb model. ...If...

I remixed this design from Thingiverse. ...The lettering on the sides didn't appeal to me, so I simply removed it.

Remix of https://www.thingiverse.com/thing:2320216. A custom mount for a relay is nestled inside this case, featuring the HiLetgo 5V Channel Latching Bistable Control Relay:...

Remix of the design by Yonatanorion. I just swapped out the switch for a new one and flipped the hole for the cables to the opposite side. Drawn up in Thinkercad. ... Update 06/20/2018: I've added a version with two holes for cable transit.

This object was created on Tinkercad. ...https://www.tinkercad.com/things/9WI4QiKPCwX

I crafted this protective cover to safeguard the exposed bottom of its counterpart from unwanted shocks and electrical discharges. Specifically, I created it as a custom fit for the original cover found at Thingiverse:...

This is a remix of Puddlefists design (see: https://www.thingiverse.com/thing:2320216). I removed existing lettering because it doesn't look great with my settings, which also created space for a fan switch. This way, the extruder-fan or existing...

Just like the original made by Elizabwth; https://www.thingiverse.com/thing:2000523/#remixes With just one modification, adding a LED/AUX switch that's a breeze to install. I used a panel mount 13.0*19.4mm SPST switch, almost identical to the one...

We require a shipment of twelve pieces each of m3x10mm DIN 965 screws and twelve pieces of m3 nuts, in addition to twenty kilograms of PLA filament.

Expanded the iconic Toranado cutout to a spacious 80mm width, giving it an even more dramatic and impressive presence. ...The tornado shape, with its swirling vortex, now boasts a larger and more striking profile that commands attention.

I designed a custom cover for my PlayStation based on other covers I had created previously to match my own console's unique honeycomb design. The cover fits perfectly onto one screw located on the right side of my 109 mm width, spring 2018 model PS....

Modified design of the original Thingiverse model (https://www.thingiverse.com/thing:2009857) boasts a sleek new look without text labels. Additionally, the switch component has been cleverly rotated 90 degrees to accommodate tight spaces - perfect...

I really loved the original design but wanted to enhance it with a DC-DC 12v -> 5v USB converter to power my Octopi from the same PSU. This one gave me the space to install the converter and room to set a cut-out for the USB port. I utilized the...

This custom power supply cover is specifically designed for the new version of the Anet A8 and comes with a fan mount for a standard 8cm fan as well as a socket for an IEC320 power switch, just like this one:...

As specified in the description, this is a basic power supply enclosure featuring a 20mm pushbutton and the capability to utilize the original cable from an Anet A8.

A Simple Power Supply Cover Boasts a Convenient 20mm Button and Allows for Reuse of the Original Cable on My Trusty Anet A8.

I believe a power supply that supplies 15A requires only a fan attached or built in, which is essentially a cover for an 80mm x 25mm PC fan.

Modified a standard power supply casing to accommodate a switch and an IEC connector at the rear, while also incorporating additional ventilation openings for improved airflow.