anet a8 psu fan 3d models

... inside a 40x40x11mm box could be used instead. The bracket will securely attach to the motor using the screws provided with the printer, and the fan is mounted to the bracket via 4mm self-tapping screws, which usually come included with your fan.

... inadequate. To rectify this, I designed and added a compact holder to the fan duct itself. I also expanded the section that interfaces with the fan, ensuring a more secure connection. ...Simply sand it down until it achieves a seamless fit.

The existing method of disassembling and reassembling screws on the fan, heat sink, and step motor can be time-consuming, especially when changing filament types or addressing broken filaments. ... This support allows users to easily access the filament...

... side can be found here: http://www.thingiverse.com/thing:1911146. Be cautious when drilling the fan. If you're up for a design challenge, a version that utilizes the holes of the fan would be great, but it's tricky to make it print in one piece too.

This adapter allows you to swap out the 40mm fan that came with your printer for a different one, specifically designed for use with this specific carriage: https://www.thingiverse.com/thing:2193695 I am using an aftermarket fan from ALSEYE on...

I cut the original fins and printed a whole new set of fins for radial fan and a whole case. Glued the fan with hot glue. Working like a charm. As per suggested, uploaded new fins design with smaller rim for better air intake. Update 31/10/2017:...

... side can be found at http://www.thingiverse.com/thing:1911146. Be cautious when drilling the fan. If you seek a design challenge, a version that utilizes the holes of the fan would be great, but it is tricky to make it also printable in one piece.

The new system incorporates a reduced size to accommodate space constraints resulting from an oversized original fan duct that exceeded height limits.

The nozzle fan for the E3D carriage was created by a talented individual named Toosha, and we're grateful for his contribution to the community.

An 18mm sensor mount is designed to accommodate 30mm fans, specifically engineered to screw into the E3D V6 30mm fan. Designs made to fit this application require careful consideration of the mounting offsets. ... For version one designs, the necessary...

... this 2-to-1 fan. ...That's great for improving your print quality. You'll need to connect the two fans in series by soldering them together. To install the system, simply attach it to the plate using zip ties or scratch marks. ...Happy printing!

I recently remixed one of my favorite fan ducts, but I wasn't entirely satisfied with its original design, which relied solely on friction to stay in position. This remix addresses that issue by incorporating a mounting bracket that allows you to...

I chopped up the original fins and designed a whole new set of fins to fit a radial fan and a full case. Then I glued the fan in place with hot glue. It's working like a charm. As per your suggestion, I uploaded a revised design for the new fins...

The human modified the fan duct by cutting it at the bottom to prevent contact with the printing components and then opening it on the right-hand side for a clear view of the print job.

I attached the 18mm sensor bracket directly to the heatsink, allowing me to remove the extruder fan from its holster quickly and easily. ...This gives me fast access to the filament nozzle throat for convenient filament loading.

- I made a cutout in the air deflector of the fan to pass through the reset button (https://www.thingiverse.com/make:371277) - I added a 3-position switch: - Position "0": Ventillo motherboard and FAN 2 (nozzle) turned OFF - Position "1": Ventillo...

I've upgraded the design by incorporating an additional cooling fan, which has yet to be 3D printed. ...Future iterations will see refinements and enhancements based on performance data.

I Made Some Changes to the Fan I Included in My Bowden Modification, and I'm Not Happy with the View I Got. ... The Original Design Can Be Found Here: Https://Www.Thingiverse.Com/Thing:1824307

Since the existing extruder setup already featured a 40mm fan, I designed this custom shroud to relocate the fan downward, allowing for enhanced cooling of the all-metal throat. The shroud smoothly slides between the lowest fin and the second lowest...

I upgrade the popular Extruder Fan Mod V2 by hadoko, found on thingiverse as thing:2290361, with a custom-designed front section capable of securely holding an Autolevel Sensor LJC18A3, featuring a diameter of 18 millimeters.

This part is untested at this time This is a remix and mashup of the following models: [blindmoe](https://www.thingiverse.com/blindmoe)'s [alternative fan mount/filament guide](https://www.thingiverse.com/thing:2147482)...

Custom Cooling Fans 4mm Longer Than Original, Allowing Cables to Pass Freely and a Secure Fixation on 50mm Fan Blower. Printing without Supports Everywhere Is Not Easy. * Update June 8, 2019 After One Month of Usage, the C-Shaped Cooling Part...

... at the nozzle, at the air outlet for the hotend. I used Thingiverse, which can be customized according to your taste: https://www.tinkercad.com/things/ePWjjEbDu9Z-fan-circular-atualizacao-edu/edit If you printed this, it's worth clicking on "like".

Although there are no problems with press-fit fan ducts, I wanted a more stable solution that uses the screws of the fan itself. An 18mm sensor holder is also included. Ended up using a "modular" design, having the plate behind the fan as a base...

LED strip mount designed specifically for use with the Spaceship Fan Duct, a popular fan duct model available on Thingiverse under ID 2088006. To assemble this LED strip mount, users will need to print it and apply ABS glue, also available on...

I created a fan cover to move my bed levelling sensor, which was attached to my fan assembly, but now that I've added a door to my fan for easier access, it's time to make some adjustments. Make sure you lay the design flat on the bed or supports...

The fan shroud used in the pictures is "Mistral 2.1" Extruder Cooling Duct for e3d Titan Aero by slimsim222 The Titan Aero carriage mount w/BLTouch is another remix I did and can be found here. Cheers again to LickenMicks for the deflector model to...

Fix the fan to the heatsink with thermal resistant glue (FAN DIRECTION: blow air into the heatsink). 5. Print or remix the STL file to enhance your 3D printer experience. 6. Use 1 x M3 screw (approximately 50mm long) and 1 x M3 nut thread for the...

Summary Using an E3D v6 Clone, a specific component cooling fan was required to circle behind the heat block on this mount: https://www.thingiverse.com/thing:2099577. Notably, a visual inspection reveals that the part shifted during printing.

I just removed the chamfer to fit my extruder carriage with the fan duct already mounted, check out the Pics for a closer look. ...I made no other changes, so the offset is still exactly the same as in buzzkc's original design on Thingiverse...