anet a8 psu fan 3d models

Adapter um ein 360W Netzteil am Rahmen des Anet A6 zu befestigen. ... Netzteil: MAIDODO JW-012H350F

For my printer, I am using a 40x20mm FLX Noctua Fan which is probably the quietest thing you can get away with for higher temperature prints while still maintaining good air-pressure & disbursement. Due to the thickness of the fan, the Noctua...

I believe a power supply that supplies 15A requires only a fan attached or built in, which is essentially a cover for an 80mm x 25mm PC fan.

I'm going to modify a 360-watt power supply into the frame of my Anet A6. ...The power supply is an MAIDODO JW-012H350F.

Airflow System for Ikea Stuva with Airflow Regulation. ...You can completely seal off the ventilation to print ASA or ABS. The cross-section is perfectly adapted to the fan. Fan: be quiet! ...Pure Wings 2 80mm BL044

You can swap out your PSU's cover to make room for a 120mm fan and a power connector installation.

You can replace cover of your psu, to be able to install 120mm fan and power connector

The fan is adjusted at a precise angle of 15 degrees, allowing for an enhanced line of sight directly towards the nozzle.

Remixed from https://www.thingiverse.com/thing:2381491 I found the holes were slightly off for my PSU so these are 150mm and 50mm spaced. ...I also wanted a 4mm offset from the acrylic uprights so that I can add a PSU cover. Print Settings Rafts: No...

I installed the fan to cool the stepper drivers - most cases come equipped with either a fan or a reset button, so I decided to combine the two protection features in one setup, hoping it meets your requirements. ... Please review the wiring...

Warning: The fan duct hole may need some adjustments for a precise fit if you're using an old fan duct. Although the dimensions should be close, I didn't pinpoint them exactly, so feel free to edit in Tinkercad. Note: An axial fan like the Noctua...

Also, placing a small LED holder in front and the fan on the right with a large flow nozzle will give you a direct view of the hotend. I recommend turning off the cooling fan when printing with ABS. You need to replace the 4 M4x8mm screws with 4...

The final product is a compact extruder fan mount that securely holds the fan in place while also providing a clear path for the filament to flow smoothly through the printer's hotend. ... To test the design, I printed it using my 3D printer with the...

Here's a parts list: * 2 M4 screws for the mount cover * 4 M3 screws for the mount * 1 M3 screw with a nut attached like a washer (check the photo) for the fan Changes Made: The fans are now located at the front and extend up to 200-210mm on the...

This way, I don't need to speed them up, and the 5015 fan performs better than regular fans. ... The Carriage Remix is based on @Dousi's design (https://www.thingiverse.com/thing:2203912) and the Clamp remix and duct on @donnyb99's work...

Additionally, installing a small LED holder in front and positioning the fan on the right with a large flow nozzle will provide a direct view of the hotend. I advise turning off the cooling fan when printing with ABS. You need to replace the four...

Two versions feature extended intake systems that bring the fan duct closer to the ground. One variation boasts five millimeters of additional length on its "horns," allowing for greater precision. ...The "three-millimeter plus" model comes equipped...

Improvement of a widely-used fan blower design now includes resizing and an adjustable vertical height feature. Visit https://www.thingiverse.com/thing:1620630 for more information. To ensure optimal airflow, it is centered based on the geometric...

... create it. With this modification, you can seamlessly switch to the hotend without having to adjust the nozzle's offset values. The entire rar package includes a redesigned semicircular fan duct that is tailored to fit perfectly with this trolley.

It's designed to fit snugly between the fan and the mounting bracket, thanks in large part to Triple_S' ingenious 40mm fan bracket. These are my Marlin Configuration.h settings: #define X_PROBE_OFFSET_FROM_EXTRUDER 40 #define...

... ...The resulting product boasts an impressive array of features, including a 40 mm fan mount, a 12 mm Z probe holder, and a Y filament joiner holder, all perfectly integrated into the E3Dv6 hotend holder design.

This is a simple adaptation of p00ta fan duct. I created it because I needed the bl-touch on the right side of the extruder. ... These are the adjustments and settings that I'm using in marlin: X_PROBE_OFFSET_FROM_EXTRUDER -30...

This optimized duct maximizes air flow and compensates for the additional distance between fan and nozzle due to the autolevel sensor support found here: http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct might collide...

This duct is optimized to maximize airflow while compensating for the additional space between fan and nozzle caused by this auto-level sensor support:http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct may collide with...

This LED Light bracket attaches directly to the E3D V6 30mm Fan using its original two lower screws. The Petsfang E3D/Bondtech setup I'm utilizing has a very limited view of the nozzle and limited mounting options for an LED bar, which is why this...

Having thoroughly examined the Anet A3's design, it was clear to me that electrical safety had been given scant consideration. A separate design for the input connector is a must, and this design is an important addition, albeit not as crucial. It's...

Anet A8 Filament Support

Anet A8 spool support

To reduce heat buildup on the motherboard, a minimalist print is necessary. ...The provided spacers must be printed and used instead of the lengthy stock spacers.

I removed residual air dams from my throat and made adjustments to the nozzle, inspired by Arjjck's design on Thingiverse (https://www.thingiverse.com/thing:1620630). ...I modified it to move the center of airflow 4.5mm outward, accommodating many z...