anet a8 temperature sensor 3d models
76680 3d models found related to anet a8 temperature sensor.thingiverse
Suporte para sensor indutivo/capacitivo para Anet A8, sendo acoplado ao https://www.thingiverse.com/thing:2290361/#files
thingiverse
A Custom Z-Axis Sensor mount for the Anet A8, using the Anet Sensor. Used for Auto Bed Leveling. Leaves plenty of room for various Ducts, and features a clip to help hold ducts such as https://www.thingiverse.com/thing:2121279 Suggest printing...
thingiverse
Settings for skynet firmware: Offsets for 12mm sensor: define X_PROBE_OFFSET_FROM_EXTRUDER -22 // X offset: -left +right [of the nozzle] define Y_PROBE_OFFSET_FROM_EXTRUDER -36 // Y offset: -front +behind [the nozzle] define...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: Indent = 2 TowerHeight = 128 EmbossHeight = 0.5 TemperatureIncrement = 4 TowerSide = 20 HeightIncrement = 8 machine = Anet A8 / 3D Fillies ABS...
thingiverse
With this sensor mount you do not need to remove or touch the sensor for filament change. Use supports if you bridging isnt perfect. NOTE, the lower hole is not perfectly aligned. Use a dremel or file to fix this. ... I will upload a fixed version...
thingiverse
... for my bowden system to let me know when i run out of filament. ...Design this unit with my Z axles sensor left over from changing to Bl touch. You will need to make two copies to forum a whole. ... i use M3*12 Screws with M3 lock tight Nuts
thingiverse
Two pieces rear support for 13mm inductive sensor. No support required. 4 M3 needed. ... Below the Marlin settings: **define X_PROBE_OFFSET_FROM_EXTRUDER +21 // X offset: -left +right [of the nozzle] define Y_PROBE_OFFSET_FROM_EXTRUDER 59 ...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: Indent = 2 TemperatureIncrement = 5 machine = Anet A8 / Anet 3D EmbossHeight = 0.5 TowerHeight = 110 BottomTemperature = 220 HeightIncrement =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: BottomTemperature = 230 EmbossHeight = 0.5 TemperatureIncrement = 5 HeightIncrement = 10 Indent = 2 TowerHeight = 95 TowerSide = 20 machine =...
thingiverse
Sensor bracket to hold Filamnet sensor above the extruder on the Anet A8
thingiverse
This is a SN04 sensor mount compatible with the stock ANET A8 extruder. ...
thingiverse
Sensor holder 18mm for Anet A8. ...Print Settings Supports: Yes Resolution: 0.2 ...
cults3d
Support for fixing the Riko SN04-N inductive sensor (Used in ANET A8) Z axis
thingiverse
Anet A8 level sensor mount plate Proximity detector sensor SN04-N --- http://goo.gl/EzS8HM Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 40% Custom Section
thingiverse
Anet A8 Probe Bracket for anet official sensor and marlin firmware
thingiverse
Another mount for the original Sensor of the Anet A8. ...
thingiverse
Anet A8 Sensor Mount for a ⌀11.7 mm Sensor. No need for nuts or washers. ... Distance from Nozzle (for Skynet / Repetier / Marlin Configuration ) : x: -25 mm y: -40 mm
thingiverse
Just a simple bracket for the 3dtouch sensor for an Anet A8. ...It fastens between the extruder fan and its heatsink and doubles as spacers for the fan screw helping to keep the fan vertical.
thingiverse
This is another front Autolevel Sensor Mount for the Anet A8 printer. My inspiration was http://www.thingiverse.com/thing:2065897 , but I liked the Sensor at an another place. Easy to install works properly with the Skynet preset. ...Was my first design...
thingiverse
Sensor Mount for Anet A8. Marlin 1.1.9 change configuration.h sensor offset. ... //#define X_PROBE_OFFSET_FROM_EXTRUDER 17 // X offset: -left +right [of the nozzle] //#define Y_PROBE_OFFSET_FROM_EXTRUDER 80 // Y offset: -front +behind [the...
thingiverse
Here is my version of a sensor mount for the ANet A8. On that other sensor mounts, the sensor blocked some way or collided with some other printed part, so I moved it in front of that fan and in the same time replaced that fan cover so that I can...
thingiverse
This sensor holder is made by my colleague in SolidWorks especially for the Anet A8 without throat cooler fan on the extruder. Additional items: m3 x40 full thread, m3 nut, some m3 washers, double sided tape and a ballpoint spring. Very cool design!
thingiverse
I designed this support for this common filament sensor I bought on aliexpress, so I can attach it to my Anet A8. Feel free to share a picture if you made one for yourself! ... The filament sensor I purchased was this one:...
thingiverse
I wanted to add a Filament sensor attached to the X carrage on my Anet A8. So I created a bracket to hold this sensor in place so that the filament route lined up: https://www.thingiverse.com/thing:2443425 I am also going to mixup the filament sensor...
prusaprinters
Another mount for the original Sensor of the Anet A8.