anet a8 x belt holder 3d models

Holder for THC-01 hotend, will also need to download my backplate, will need both parts to make it work. ... This is adapted so you can put the thc-01 on an anet a8 printer if you are upgrading nozzels.

this is a simple filament holder for the top of the anet a8. uses 4 - 608 skateboard bearings no screw needed but i have added a hole for one on each bearing just in case... ...

Install the Anet A8 spool holder directly above the LCD display in the middle. ...It demands an 8 millimeter bar or threaded rod that is approximately 240 millimeters long.

Here are some questions: Where did you get your nipper from? ...The thingiverse website says Anet A8 printer holder. ...Is it possible that they got the parts somewhere else and just put a sticker on them?

I crafted a custom attachment for the Anet A8 Spool holder, enabling users to accommodate multiple spools of filament at once. ...To achieve this, additional support is required in the form of a longer rod.

Improved Y-Axis Belt Alignment: Enhance Your Printer's Performance Secure and level up your Y-Axis belt by pairing two identical parts, which allow for precise tensioning against the H-Frame. Four button head screws (4mm x 25mm) and two set screws...

another Y-Belt tensioner with screw

it is simply the stock anet a8 spool holder but double sized to allow 2 spools to be held at the same time. you need to print 2 pieces of each part in order to assembly it. you may also consider to print the spool holder i designed...

Since my printer is not actually an Anet A8, it lacks the spacers under the circuit board found in the original design. To install Leo_N's mosfet holder on my printer, I required longer spacers for the opposite end of the circuit board. ...Therefore, I...

... a M8 mount on top that allows for seamless integration with a threaded rod. Be sure to finish the M8 nut holder with a side cutter after printing. Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 4%

... On top, I can store up to 6 SD cards. Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 50% How I Designed This I designed this holder using Rhinoceros 3D software.

This is a stock Anet A8 spool holder, but doubled in size so that it can hold two spools at once. To put this together, you will need to print out two of each part. You might also want to consider printing the spool holder I designed at...

I've been using Prusa Y Rod Holders on my Anet, but one of them wouldn't fit due to the Anet's endstop. To fix this issue, I decided to remix the Prusa design to accommodate the Anet endstop, and you can find the result here. ... This modification works...

Anet A6 / A8 power supply holder. When the Anet printer is in a box, such as an ikea table box. The printer power supply must be out of the box to prevent overheating. ...We attach this holder to the leg of the box from the outside.

One of the original bearing holder of my Anet A8 broke, so I printed this replacement. The bearing holder from https://www.thingiverse.com/thing:2791727 was quite similar but I had to modify some small details to make it fit.. ... Print Settings...

You can easily create a simple SD-card holder for your Anet A8 to prevent losing them again and again. Print Settings: Printer: Anet A8 Rafts: No, rafts are not required for this print job. Supports: This design does not need any supports to ensure...

... may need some force to securely fit the Playstation Eye Camera into it. Once fitted, however, it will hold the camera firmly in place. To assemble this mount, attach the disc to the holder using an M3 screw and nut left over from the ANET A8 build.

... bed Anet A6/AnetA8. ...It prevents sparks and accidental disconnection of the plug. Compatible with the thermal insulation of the heat bed. Based on conception Anet A8 Hot Bed Strain Relief by jasonletchworth http://www.thingiverse.com/thing:2066067

I've adapted the Heliox Anet E10 pen holder to fit my Anet A8 perfectly. Other available parts can be found on the original design here: https://www.thingiverse.com/thing:3271566 A huge thank you goes out to her for making this possible! ... Enjoy my...

... too. Print Settings Printer: ANET A8 Prusa i3 DIY Kit Rafts: No Supports: No Resolution: 0.3mm Infill: 10% Notes: Renkforce 1.75mm PLA filament used. Slic3r with Rectilinear fill patterns applied. ...Extrude-Temperature: 210°C Bed-Temperature: 53°C

A Handy USB Accessory Clamp Tailored Specifically for Anet A8 Printer Sides' Dimensions

The Anet A8 raspberry pi camera mount securely fastens to the hotbed screw holes.

I'd like to get a plain version without the Anet A8 branding on it.

A Handy Wrench for Anet A8 Spool Holder. The Spool Holder Seen in the Picture can be Found Here: https://www.thingiverse.com/thing:2226146 This Device was Created using Freecad Software. ... Please Keep in Mind that the Quality of the Spool Holder in...

I started printing with my Anet A8 on the first day by creating a center spool holder to improve the spool's rotation on the original holder. This was a straightforward approach, leading to better prints later on. ...To accommodate one standard-sized...

I broke two of the supplied acrylic clamps, because I put them on a little too tightly. ...My clamp has the same size with a recess for the Y-axis belt. ...It fix the belt but cannot break that easy.

This replaces brittle acrylic straps holding the belt on the bed's bottom for the Y-axis, also improving belt geometry by lowering the belt a few mm to align with the pulley. The belt ends slip into block halves and out through the hole. When loose,...

This spool holder takes over as the upper left frame cap on the Anet A8 printer. It seamlessly integrates with the threaded spool holder rod that comes pre-installed in every Anet kit, elevating the printing experience to a whole new level. ...This...

I lengthened the primary body of the tensioner to accommodate a shorter y belt, which was initially insufficient for proper installation. The added length allowed for a more relaxed fit once the plate was applied. ...This modification enables the use of...

An Alternative to Standard USB Holders, This Design Focuses on Lateral Coupling for Enhanced Stability and Compatibility with the Anet A8. Key Features of This Innovative Holder Include: A Precise Fit Guaranteed by Good Tolerances Ensuring a Secure...