anycubic 4max pro fan 3d models
187129 3d models found related to anycubic 4max pro fan.thingiverse
This is PRO version of fan duct dedicated to Anycubic 4MAX PRO. ... Easy to print just use ABS and supports from base only.
thingiverse
This is my latest design of very efficient cooling duct for Anycubic 4Max Pro. It is so good and strong that you need silicone cover for your heat block. You can print it from PLA and ABS. This cooling duct is far away from heating block so it is...
thingiverse
**Print settings:** Print the **fan_duct_symmetric_rotate.stl** in the provided orientation or try experimenting with the **fan_duct_symmetric.stl** on your own to find the best orientation. ... In both cases you will need some supports (touching...
thingiverse
Circular fan duct based on the https://www.thingiverse.com/thing:4167848 Added additional mounting point on the opposite side to prevent it from sagging and for more precise positioning. There is a second threaded insert in the stock carriage already...
thingiverse
Every part cooling duct I have tried on the 4max pro has eventually sagged down and begun catching on parts after a while of printing ABS. Not good. What all of these ducts have in common is that one side or the other is simply too close to the...
thingiverse
This is Remix from dual to tripple fan duct. A two-part fanduct is printed with backing from the table and is not as demanding for printing. Next, it should be glued. ...for correct printing, you must turn part 1 upside down
thingiverse
Anycubic 4MAX PRO carriage evolution+360 fan I have spent many hours trying to repair the original carriage and in the end I have decided to make a new one. improves the impression by far. ...I hope it helps you.
thingiverse
Cyclone fan duck for Trianglelab v6 Brass Heatblock and V6 Nozzle
thingiverse
This is my bes variation of 4max pro fan duct. ...M3 10 Bolt.Enjoy!
thingiverse
Немного изменил для установки в 4MAX PRO
thingiverse
I did this airflow because stock airflow is no good. This one works well. A two-part fanduct is printed with backing from the table and is not as demanding for printing. Next, it should be glued. ...for correct printing, you must turn part 1 upside...
thingiverse
I modded the original STL (the model itself is not perfect, but works) for a better cooling and to avoid melting and deformation due to high temperature during ABS prints. ... Use ABS for this, not PLA.
thingiverse
This a remix of my favourite fan duct design for the 4Max Pro, adapted to fit the 4Max Pro 2. This is not an elegant remix, its very hacky but it works like a charm. It's designed to use the stock hardware. ... Happy Printing
thingiverse
- Pull the PSU out a bit, without straining the cables - Unscrew the four screws holding the PSU's cover - two on each of its long sides - **BEYOND THIS POINT, THE MAIN CAPACITORS ARE EXPOSED AND YOU SHOULD BE CAREFUL NOT TO TOUCH THEIR LEADS, AS...
thingiverse
The 4Max Pro by Anycubic is a fantastic printer. However it comes with a little spout that blows air from one side of the nozzle. That usually means stringing and sloppy overhangs when the filament leaves the nozzle on the opposite side. This new...
thingiverse
I made this because I couldn't find any fan ducts designed for the 4Max Pro 2.0 that would work with the stock hotend and an E3D V6 Nozzle. It's not my design originally, as I simply modified one that had already been made. I shortened the "tower" of...
thingiverse
Design far from perfect, but it is better than hot air blowing on drivers.
thingiverse
print it with supports only from the hotbed there is a version for a volcano
thingiverse
This fan adapter allows to replace the radial fan below the air filter on the Anycubic 4Max Pro 2.0 with a 40 mm fan, without changing other parts. ... The part was designed to fit a Noiseblocker BlackSilent XM-2 fan.
thingiverse
ABS print. ...4Max pro BMG anycubic. I use the right bmg. You need a hole(blue) in the bmg(yellow) for the bolt(red) for attaching the hotend radiator(black). ... You can install stock plastic (black) mount in BMG
thingiverse
Filament Spool holder for Anycubic 4Max Pro. Mounted on the position of the Filament Sensor and with the same screws and 2 washers. Filament spool holder for 1kg spools with a maximum of 95mm width. V1 is a visually massive construction, but...
thingiverse
Ich habe mir der Filler https://www.thingiverse.com/thing:3020026 für meinen 4Max Pro angepasst. Optimal für 1kg Filamentrollen. ... Über einen Café würde ich mich freuen paypal.me/GeorgAndryk
cults3d
... core for the filament roll holder. You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange
thingiverse
... for the filament roll holder. You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange
prusaprinters
You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange Print Settings Printer Brand: Prusa...