anycubic extruder upgrade 3d models

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

A remix from a cooling duct found on printables https://www.printables.com/model/214808-anycubic-kobra-cooling-fan-duct Based on the 2mm offset design found on printables which you have to cut down the left side for it to fit the Anycubic Kobra. I...

Führung für den Bowden Tube am Druckkopf des Anycubic vyper. Passend für mein Remix: https://www.thingiverse.com/thing:5071604 Der Sinn dieses Teils ist es, die Kräfte, die sonst am Cold End ziehen bei Bewegungen in X-Richtung abzufangen. ... ...

To connect the filament guide to the extruder, I utilized the bowden connector from the original extruder that comes bundled with the Chiron printer. The trianglelabs BMG extruder I used can be purchased through Aliexpress; simply click on the link...

A Bracket to Rotate the Extruder for Easy Filament Insertion To accomplish this task, you will need four M4 threaded screws and four M4 nuts.

Manufacturers are now offering extruder support for easy installation on a horizontal mount with a convenient front-facing filament input, all integrated right onto the Z-axis carriage.

I extended the arm by an extra 10 millimeters using Fusion360, which fit the stock extruder flawlessly. ...My current Z-Offset reading is minus 49 point 69.

This is a Simple Adapter to bridge the gap between the Filament runout sensor and the white bowden tube of the extruder. ... Makes guiding filament throught way easier.

Replacement for the standard i3 Mega S extruder filament guide. ... Use a 2mm drill bit to ensure filament guide hole is correct.

... downloadable from https://www.thingiverse.com/thing:865929. ...Next, I securely fastened the extruder to the upper rail, positioning the bowden tube downward for optimal performance. ...This versatile bracket provides a solid hold on the extruder.

... extruder with a specific purpose in mind. ...I wanted to be able to spin it quickly and easily, so I could gauge its speed firsthand. Additionally, I wanted to have the ability to manually feed or retract filament from the extruder using just my hand.

... ...By positioning it in this way, you'll have unobstructed access to the extruder from the front side, making filament changes significantly easier and more convenient. This design is particularly well-suited for enclosures where space is limited.

The Extruder Drive Motor Mount secures itself firmly onto the bottom rail, positioning the extruder drive motor in a stable and reliable manner. ...To prevent any potential damage, this mounting point should be situated near one of the Z-axis risers,...

This adapter plate turns the original existing Bowden extruder into a direct extruder with simple means. The existing mounting bracket is exchanged for this plate and fastened with the two top screws of the X linear guide. I printed the plate out...

There are numerous false claims about what causes the "click", such as: the extruder motor lacks sufficient torque; or the extruder gear slips. However, none of these explanations are accurate. The real cause is this: the original metal extruder...

This is an adaptation of a compact fly extruder created by Mauro that caught my attention due to its unique design. ...I decided to modify it to suit my own setup and needs.

The Thumb Bar on my extruder broke, so i created a extender that will fit over the stock one to. A: make my repair. B: extended it to make it easier for me to use. ... 2xM3 screws hold it together.

I extended the bracket to give myself room to adjust the extruder downward, thereby shortening the Bowden tube and creating a gap between it and my top-mounted filament guide.

The design aims to avoid any sharp flexing points by guiding the cable in the direction that it naturally sits. The 2020 bracket clamps to the frame near the power supply, and the cable clip attaches to the top of the extruder. You may need a couple...

I integrated several extruder mods to create a single unit that boasts an extremely tight fit between the extruder motor and bowden tube, further reinforced by my own additions.\r\n\r\nIt's been running smoothly for about a month now. No jams have...

... sits. The 2020 bracket clamps to the frame near the power supply, and the cable clip attaches to the top of the extruder. You may need a couple of slightly longer (~12mm I think) m3 screws. ...The cable is then held in place with a few zip ties.

The 2020 bracket attaches securely near the power supply, while the cable clip fastens directly onto the top of the extruder. You'll need a couple of slightly longer M3 screws, approximately 12mm in length, to secure everything properly. ...Finally, zip...

It appears that you are describing a custom 3D printer setup with multiple extruders and a pneumatic system. The requirements include: 1. A Nema17 stepper motor with a specific configuration. 2. An extruder set with a certain type of hotend. 3. A...

Since I'm revamping my whole 3D printer setup, I need a plate situated between the extruder and print head (see attached image; the extruder hangs low over the print head without placing weight on it, but isn't swinging as hard anymore). Additional...

https://youtu.be/zHyY3Y1sMZE It would be wonderful to receive donations, as my project has exceeded my expectations and I already have two additional projects for the Anycubic in the works. Thank you very much! Update 24.01.2019 All final printing...

... figure out that I could reduce it's size almost twice. ...Just with this simple upgrade you will be able to have 2mm of retraction settings.Youtube: https://youtu.be/DRXus4slqecUpdate:v1 - added corner for part strengthv2 - added point for plastic feed

... mini cover. ... you can see the inside of Extruder. also you can easily put filament in it. note: this thing is work in progress now. It's not 100% completed, so you may have problems with screw tightening. ... but for me, it's working nicely.

Extruder Mod for TPU with Pressure Reducer Works Flawlessly with All Filament Types. Forget about Support Structures at the Joint! To Ensure a Secure Print, Use 100% Infill for the Screw. Update V2: * Slightly Adjusted Hole Position for Better...

The cable coming off my extruder often hit the top bar of the printer when I printed tall objects. Crafted this bracket to mount seamlessly on the existing hardware. Gives it a bit on an angle and keeps the cable back and out of the way. ...

The clip locks firmly onto the extruder motor from beside it, its smooth edge gliding effortlessly over the motor's rear as it swings open to make contact. ...Pressing it home secures everything in position, allowing you to carefully guide the harness...