anycubic extruder upgrade 3d models

Dies ist ein Umbau wo den Serien Extruder quasi als direkt Extruder einsetzt.Lediglich die Extruder Kabel müssen verlängert werden, und ein paar längere M3 Schrauben werden gebraucht.Ich Slice nun über den Bambu-Slicer und habe kein Stück Stringing...

Maketos Excellent Corner Brace gets a fresh spin for the Kossel. ... Here's the updated version, polished to perfection for a cleaner extruder wire guide.

Here's a high-quality, simple Bowden Extruder designed specifically for use with the MK8 Drive Gear and the reliable 625ZZ Bearing, ideal for Kossel Delta printers.

The screw connection between the extruder and hotend is necessary because this particular extruder only has an M10 threaded outlet. Fortunately, the x-limit switch remains functional. Hotends V5 / V6 and Volcano are compatible with this setup, and a...

side holder for extruder BMG and original double-sided, adjustable (left / right side, ....) tested, works well 360° rotatable solves Z-wobbie and ghosting V1 > first relase V2 > fix hole V3 > thinner by 2mm (printed faster while maintaining the same...

... loose, causing the cable to lose its guiding alignment. To prevent this, the cable holder has been installed under the extruder using its mounting screws. ...The cable can be inserted into the guide and fastened with a cable tie for added stability.

Extruder and hotend are screw connected, because this extruder just have an m10 threaded outlet. The x-limit switch still works. Hotends V5 / V6 and Volcano fits. A bltouch can be mounted. The stock level sensor can’t be used in this version, maybe...

I modified a drag chain holder, known as "Schleppkette A," originally designed by user Michelix, so that it can be used with a side-mounted extruder-mod like the one created by Sensibelchen_AB. The modification can be found on Thingiverse at...

I have increased its size and made adjustments to ensure that my printer's extruder can be supported from above. To verify this, test the longest screws for holding the extruder in place. Longer screws may push the piece out of its correct position....

This is a modification of the Delta Corner Foot by Akya2120:\nhttps://www.thingiverse.com/thing:2202372\nI increase size and resolve issue to support on top of my printer the extruder.\n\nTest longer screws for supporting the extruder, longer screws...

Just added a support fot the X-axis switch to use it in my Anycubic Prusa i3. Also added holes to mount Bltouch/3DTouch sensor. The bad part is that you will loose some X and Z mm. UPDATE 20/02/21 New V2 version. Added holes for...

To address this issue and allow for a printed extruder bowden attachment that's TPU capable, I need the entire extruder side to be cool as well. I've attached a picture of a previous attempt without active cooling, which resulted in deformation...

To create the necessary airflow pathway, I devised a quick solution involving a duct/mount combination that effectively cools the extruder while also accommodating its limited clearance. This setup can be easily adapted to fit the i3 Mega extruder's...

The CR10 Direkt Extruder, a vital component of 3D printing, is seamlessly integrated into the V6 Hotend system. This innovative combination enables efficient and precise control over material flow, ensuring high-quality prints. ...The integration also...

... incline, approximately 100mm of Bowden tube is saved. Cable Chain: http://www.thingiverse.com/thing:3668667 The chain holder on the extruder side is a remix of: http://www.thingiverse.com/thing:2860786 Support is only needed for the chain holder.

Tools: * Hex keys that came with your Chiron * Wire cutters * Soldering Iron Supplies: * 1 Meter 22-26awg wires to extend the Extruder motor cables * M3 x 8mm Screws - 3 * M3 x 12mm Screws - 2 * M3 Nuts - 3 * Bowden tube fittings with 5mm Thread *...

... it just a bit. But it might stretch from heat so. it is what it is Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Resolution: 0.1 Infill: 80 Filament: UNKNOWN PLA Green Category: 3D Printer Accessories

I'm excited to share with you a game-changing Extruder Mod that unlocks the full potential of TPU flexible filament. This precision-crafted mod ensures seamless performance and optimal results. To get started, simply drill a 2mm hole into your...

... the overhead cabinet, you'll encounter two main challenges: 1. Extend the wiring harness of the filament sensor for proper functionality. 2. Rotate the extruder motor 180 degrees due to the short wiring harness length for that specific component.

Haruka Ze's Direct Extruder Installation: Cable Retainer Production To secure the cable to the main body, I created this part: https://www.thingiverse.com/thing:3954252 I replaced the original bolt with a 35mm M3 panhead screw because it was too...

With the extruder in a new position, something needed to be done about the cabling so I've included a couple of cable guides in the downloads section as well. A link to another one of my cable guides for the hot end can be found below. If you print...

To build the exact extruder as pictured, you need to print all 4 parts (remember to mirror the end_plate and midsection) along with the mirrored version of the original M4 STLs (except the main body and the end plate since you'll be using this...

With the extruder in a new position, something had to be done about the cabling so I've included a couple of cable guides in the downloads section as well. A link to another one of my cable guides for the hot end can be found below. If you print...

As I didnt want to disassemble the extruder, I created my own mount that can be used with the stock L bracket that comes with the titan extruder (on Mega S). I believe it is a steel bracket and its is extremely strong so there should be no problems...

This mod allows you to adjust the filament pressure on your original extruder/feeder. You can now influence the flow and avoid the risk of radial wear on the filament. To install this modification, follow these steps: 1. Print the mod. 2. Shorten...

I found some mounts for Mellow's BMG Aero and Anycubic i3 Mega (S) but all of them was a bit disappointing. So I created one myself. With drag chains, LED light, integrated X belt tensioner an so on. I tried to use as much stock components as I can...

This side holder for BMG extruder is a game-changer. It's double-sided, adjustable and made to be used on either left or right side. The good news is that it has been thoroughly tested and performs exceptionally well. This innovative design also...

I want the extruder on the X-axis and, of course, don't want to drill new holes or threads. So, I designed this mod, and it works great. It's printed in PETG, and you'll only need two M4 nuts and four M4 screws 15mm. Of course, this solution may...

I also included an "untested" version that allows using the extruder without cutting off the lid, but since I've already cut mine off and installed it, I unfortunately can't test it. Pro tip: if any screw you have is too long for something, just...

Material´s List: 1 unit Linear Rail L500 MGN12 ( block type C or type H)            cheap option 1:           cheap option 2:My recommendation is to use the original Hiwin, more...