anycubic i3 mega anti z wobble by 3d models

Hotend cover components for the AnyCubic i3 Mega feature significant fan inlet designs. ... Caution: The correct cover must undergo a mirroring process.

This is my design for a webcam clip for my Anycubic i3 Mega-S. ...I wanted to do timelapse and keep focus on the model.

Modifica del coperchio alimentatore della Anycubic I3 Mega per installare una ventola da 80mm e abbassare la rumorosità generale Category: 3D Printer Parts

... on for this print to work correctly. You may need longer screws (M3x10 screws) for this project. On my Anycubic I3 Mega, M3x6 screws were not sufficient, but you can try using them first and then decide if you need to upgrade to M3x10 screws.

Replacement Filament Sensor Enclosure for Anycubic i3 Mega. Designed to bolt onto the outside of the printer's right side, where the z-limit switch is secured with a fastener. The enclosure uses shorter M3 nuts and bolts to secure the sensor in its...

This is a precision-crafted vibration damper leg specifically designed for use with the highly-regarded Anycubic I3 Mega S 3D printer model. ...Measuring precisely 20 millimeters in diameter and 15 millimeters in height, this component plays a vital...

This is a versatile battery holder designed specifically for use with the Anycubic I3 Mega. If you're looking to illuminate your workspace without relying on the power supply, this innovative solution is just what you need. ...By attaching a low-voltage...

This is the upgraded version of "Anycubic i3 Mega Spool Holder", brought to you by CuriousTech. It features a slimmer design and a reduced number of parts, leveraging the original spool bar for simplicity. ...I've also refined the snap-on part for...

This is a new cover designed specifically for the Anycubic I3 Mega fan. It relies on M3 square nuts, each measuring 5.5mm in diameter. To facilitate easy remixing, I have included both Fusion 360 and step files. ... The design concept was inspired by...

Simple tool holder for the main supplied tools of the Anycubic i3 Mega, including one additional place for tongs and a small knife and also for an scraper scaled to 55%. The tool holder is fixed by two screws next to the voltage switch on the...

Anycubic I3 Mega Filament-Holder:\r\nSecure the holder (Part1) by screwing it in place using four screws attached to the right vertical crossbar. ...Insert the U-shaped coil holder (Part2) into its designated recess, ensuring a snug fit until it clicks...

A versatile handle for the AnyCubic i3 MEGA hotbed, allowing effortless movement back and forth. A simple clamp securely holds it in place. Original design by GMK666. Since my plate was missing a hole, I thought up this version, designed and...

Tool Caddy for Anycubic i3 Mega. You'll notice a reduction of approximately five centimeters in printable size height due to the tool caddy design. The tool caddy accommodates all tools provided by Anycubic, including a caliper and a set of key...

... that smoothly guides the cable into place. The holder is specifically engineered for use with the Anycubic I3 Mega equipped with the Ultrabase, as the hole pattern and connector clearance differ from those found on the standard I3 Mega model.

... Griff für das Druckbrett des Anycubic I3 Mega S mit flacher Befestigung am Druckbrett. ...Ausreichender Platz zwischen Griffbestigung und Abdeckung (von mokush / Anycubic i3 Mega Y pulley cover) für die Umlenkrolle des Transbandes für das Druckbrett.

Decided to design and print new bearing holders for my Anycubic I3 Mega for the Y axis (bed). These were designed for the Igus Drylin RJ4JP-01-08 bearings. They snap fit into place and won't move. ...I printed these on my Anycubic I3 Mega.

... proper printing, you need to enable supports for this model. PS2: You may need longer screws (M3x10 screws) to securely fasten the cable in place. The Anycubic I3 Mega uses M3x6 screws by default, but M3x10 screws will make the process easier.

To explore more designs for the AnyCubic i3 Mega, visit my collection on Thingiverse: https://www.thingiverse.com/dtylerb/collections/my-anycubic-i3-mega-designs If you found this design helpful, consider showing your appreciation with a tip or...

I tried to use them directly in my Anycubic I3 Mega but had two problems: - The nut is very close to the Z endstop and touches when it turns. I rounded the top half of the nut and now it rotates perfectly. - When I tried to disassemble it, I...

Parts required: - PC4 M6 pushfit connector (one that feeds the reverse bowden tube all the way through) - At least 60cm bowden tube My Anycubic i3 Mega designs can be found in this collection:...

... Rod. ...In this scenario, I employ an 8mm rod and a laser-cut acrylic frame. Designing This Project Requirements Non-printed Components: M3 screws, nuts, and washers in large quantities Printed Parts: two z_wobble units one z_wobble_base_prusa_i3 unit

The Anycubic I3 Mega fan cover is a crucial component of this 3D printer's overall design and functionality. This particular part, referred to as the "fan duct side/left," plays a significant role in ensuring efficient airflow within the printer's...

Having experienced a broken filament release handle on my own Anycubic Mega S, I opted to replace the entire extruder assembly with one from an older I3 Mega. The new assembly is superior in terms of material and build quality, featuring aluminum...

... over-extrusion by monitoring the extruder temperature and adjusting as needed. By following these guidelines, you can master the art of working with filament on your Anycubic i3 Mega and achieve high-quality prints that meet your expectations.

Rahmenblende für den Anycubic i3 Mega S. Wer zu viel Filament und Zeit hat, hat hier was zum aufhübschen seines i3 Mega S. Ich hoffe, es gefällt. Weiteres in der Anleitung (pdf). Das sind viele Teile, werden aber nicht alle benötigt. Je nach dem,...

Levelling knobs for Anycubic i3 Mega - simply slip them on until they hit the existing levelling nut, making it much easier to level the bed, especially at the back of the print bed. ... As shown in the picture, this is for the brass-style levelling...

It's specifically designed to accommodate my Anycubic I3 Mega machine on the front left corner. This versatile holder can also store two SD cards and other handy items such as a touch pen, an SD card USB reader, or tweezers. ...Have fun printing with...

This is a remix of this thing: https://www.thingiverse.com/thing:629886 Thanks go out to nigeljohnson73 for his exceptional design. ...I have incorporated a holder that secures the Bumper to the Anycubic i3 Mega.

Anycubic i3 Mega LED Halter can be directly connected to the 12V fan. ...This device was created using Tinkercad and can be edited online at https://www.tinkercad.com/things/jq1k8b2s7Om.

Hello everyone, I've just developed a basic prototype of the Anycubic I3 Mega. In theory, this new design should enable printing with even smaller dimensions. ...However, I haven't had a chance to test it out yet.