anycubic i3 mega filament not feeding 3d models

this is a filament guide i modified to mount the standard anycubic mega s filament sensor to. it lines up perfectly and allows you to feed filament straight into sensor and out other side without having to reach around the back and fiddle with...

I'm using it on my custom Anycubic I3 Mega, but it should work on all types of Prusa printers with this mount: https://www.thingiverse.com/thing:926794. The fan duct isn't ideal, but it works. Unfortunately, it's not as good as the stock one. If I'm...

Materials needed: * 1x M3x20 * 1x M3x25 * 4x M3x8 or M3x10 * 1x Kitchen sponge * 1x 80mm 12V LED Ring Original sources: Improved Logitech c270 Manual Focus System https://www.thingiverse.com/thing:3081838 by codiac2600 Sep 3, 2018 LED-Ringhalter für...

Anycubic Mega S Filament Stand: Print with Support, Follow Photo Reference Stand Firm for Liberty, Unite Behind Hong Kong's Cause. ... Five Unwavering Demands, Uncompromising Unity - No Exceptions.

This adapter is specifically tailored for the Anycubic I3 Mega 3D printer. It works best in conjunction with my custom filament holder: https://www.thingiverse.com/thing:3409461 The original system with a magnet is unreliable and prone to failure,...

This feeder lever of the Anycubic i3 Mega S is a sparepart that causes less friction while extrusion. This is possible because of the 12mm PTFE insert inside the feeder.   Just Print the part. Cut a 12mm log standart PTFE tube. Insert it inside the...

Design to support a 628 (8x24x8) bearing. ... Original one from Trida :https://www.thingiverse.com/thing:3251419 Print Settings Printer: Anycubic i3 Mega Rafts: No Supports: Yes Resolution: 0.2mm Infill: 30%

It's designed for the Anycubic Mega-S which has the filament sensor screwed to the side of the frame. This screw is used to attach this filter. Probably the other Mega variants have a similar fixing... During installation or on a filament change,...

Since I had a webcam handy and it works great with my Raspberry Pi via Plug&Play, ideal for OctoPi, I was looking for a way to attach it to my I3 Mega S. The model S comes standard with a holder for the filament, which is perfect for it. This metal...

... ...The roll now mounts in the same position but higher, making it more convenient to use. A 3mm screw holds the top part in place. A separate link for the filament is included as an add-on and not printed on the original holder shown in the picture.

Hi, So I put a new roll of filament on my Anycubic Mega Zero and it is so tightly wound that the filament would pull back and sometimes the roll would jump/ skip after the extruder pulled hard enough on the filament. I decided to make a quick...

These caps are designed to work with Anycubic filament spools. They allow your filament spools to spin round smoothly without snagging, which prevents a lot of 3D printing problems. There are two diameters available: 75mm, 58 mm and 56mm, so you can...

As my hot end traveled left and right on my x axis all my work to quiet my Mega S was a waste because the filament was making a racket against the spool holder. ...I made this bracket to hold the fist (print fist at 50 percent size) I mirrored the...

As my hot end traveled left and right on my x axis all my work to quiet my Mega S was a waste because the filament was making a racket against the spool holder. ...I made this bracket to hold the fist (print fist at 50 percent size) I mirrored the...

Adapter to directly connect a bowden tube from the filament enclosure (e.g. ...IKEA Samla) to the Anycubic i3 Mega's filament sensor.

First submission. ... A simple filament guide, made by using the measurements of the original end-caps of the 2020 aluminum.

I started using a usb printer cable to connect my printer to my PC and I noticed the filament reel would rub up against the usb cable. ...This riser is placed on the existing filament reel holder to raise the reel by 20 cm (~.8 inches) which is enough...

I had been using a custom filament holder for quite some time, based on this design I remixed it from, but found other cool holders that didn't quite work as intended so I combined these three filament holders to position the roll further back and...

A filament guide to replace the stock spool bracket and smooth the path when using a dryer box. ...Slips on to the same 2 screws the original bracket uses.

This design can be used in conjunction with a filament gear knob (available at Thingiverse under ID 2747964), although it may slightly impede air flow onto the filament. Nevertheless, it should still provide adequate cooling performance. ... The...

Fan Holder for Anycubic I3 Mega S

Anycubic i3 mega aeration & anti vibration system

Fan duct for Anycubic i3 Mega printer.

Anycubic i3 mega aeration & anti vibration system

Verbesserungen Anycubic i3 Mega S,X,Pro.

Nozzle cooling duct for Anycubic i3 Mega. ...

After completing the LED Holder V2 (https://www.thingiverse.com/thing:2637201), I discovered that the Filament would experience problems during prints when placed on the new filament holder. It appeared that all filament guides I searched for ended...

Design supports a 608 skateboard bearing and larger for smoother filament flow.\r\n\r\nOriginal design from enry68: https://www.thingiverse.com/thing:2846692\r\n\r\nAdditional note: Check the last picture, flip the filament sensor holder upside down...

All you need is: - 3x ball-bearing (12x28x8 mm) (ID x OD x W) i used S 6001 RS - Drill or cut a smal notch in your original filament holder - 2x nut and bolt M3x16 No supports needed. ... You can adjust the width to your filament role and the tension...

Sometimes the Hole in the Filament gets bigger than expected, and that's where this Cone comes in to save the day! You can use it to fix those pesky issues with your 3D prints. ... Made by Alessandro Iron-Man Forciniti, this innovative solution is based...