anycubic i3 mega filament 3d models

... 2 to the adapter plate. You could potentially use four M3 machine screws instead, but I haven't tested it (the screw hole opening is 2mm in size). Print Settings:Filament: Polymaker Polylite PETG, TealLayer height: 0.2Perimeters: 2Infill: 25%

I also thinned some walls (it's a messy and quick edit) to save some time an filament. Hopefully it will work this way. ------------------------------------------------------------------------------------------------------------------------ ...

This allows for easy removal while working on the extruder, such as feeding filament. The fan is secured with two coarse screws. Given sufficient clearance, you can attach the fan from both sides. There are likely more sophisticated solutions to...

... of mine for as long as I can remember, seems like it is about time I made something for the LED to sit on that directs its light straight down. Untested until I load some transparent or white filament again... ...might try it with grey just to see.

This model is remixed from:https://www.thingiverse.com/thing:2917729 The TUSH spool holder is here:https://www.thingiverse.com/thing:2047554 I found out the hard way that it barely didn't work on my printer, and decided to at least put the...

Filament dust filter for original Anycubic Mega S filament holder. No screws neccessary. (Clamp it) Quick designed. Printed with PLA. No special settings. ...

... they arrive from Amazon). I modified the i3 Mega "Ultimate" bracket by @libertyprime04 to make it compatible with the Mega X - https://www.thingiverse.com/thing:4214315. ...This should be helpful for anyone with a newer Anycubic Mega X printer.

This is a remix made suitable for the Anycubic Mega Zero and based on my other design of a filament guide: https://www.thingiverse.com/thing:4626077 There are 3 mounts that have different heights to the extruder. Depending on your setup and...

This is a file for a filament sensor mount on the Anycubic Mega X. It is meant to replace the factory mount in case that it is damaged or missing. ... Can be printed via Resin or Filament.

... MegaZero 2.0 printer. ... This is a modified version of the adapter discussed in this thread on Reddit: https://www.thingiverse.com/groups/anycubic-mega-zero/forums/general/topic:48565 . ...Credit goes to Calvin_Megazero for the original design.

This sleek card holder is designed specifically for Anycubic I3 Mega S 3D printers. ...It requires no removal of the support screw for easy mounting.

A filament spool holder to fit the Anycubic Mega Zero. ...Uses two 608 bearings to reduce friction and is assembled with an M4 x 60mm bolt (two washers & lock washers recommended) Should fit any printer that uses a spool holder mounted to a metal...

UPDATE: I made the holder slightly wider to give the bearings more space to move freely. I also added a divided roller to glue them together. This Filament roller is for the I3 Mega-S and the upgrade kit. Started remixing and ended recreating it from...

Based on a great idea of Ivader posted on https://www.thingiverse.com/groups/anycubic-mega-zero/forums/general/topic:48565 , this is an universal mount for a Simple filament sensor like https://www.aliexpress.com/item/32967361574.html It uses the...

Most of them required screws and were designed specifically for the original AnyCubic i3 Mega, so I worried about clearance issues with where the Mega-S has the spool holder, filament sensor, etc. I wanted to be able to mount it either on the front...

This versatile card holder is designed specifically for Anycubic's I3 Mega S 3D printer. ...The unique feature of this card holder is that it can be mounted without removing a single screw, making installation quick and hassle-free.

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the Anycubic...

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the [Anycubic...

It'll fit the sides of the frame snugly and won't slide up or down by itself meanwhile not interfering with the Z axis carriage. This design is symmetrical an can simply be flipped to fit on any side you like. To screw in the extruder you'll need two...

This Filament roller is for the I3 Mega-S and the upgrade kit. Started remixing and ended recreating it from scratch in Fusion 360. It is a shorter version, as my filament spools only have a maximum width of around 6.5cm, the roll has 6.8cm. ...

Guardate qui anche gli altri miei progetti: https://www.thingiverse.com/mbellucci/designs It was designed for the Anycubic I3 Mega, to keep the wiring and spool tube vertical, thus avoiding interference with the top crossbar as Z increases. In this...

I lost the tiny centering aid / filament guide thingy that came with my Anycubic Mega S and was pretty bummed to find out that nobody has designed one of those yet. Am I really the only one in desperate need of such a cap / guide / centering aid? ...

Rev04 is intended for use with the Calvins "Universal mount for a Simple filament sensor" https://www.thingiverse.com/thing:4650358 The Major change is to make it compatible with the "Anycubic Mega Zero lead screw stabilizer" by drogica. I simply...

A simple design for a filament guide for the Anycubic Mega Zero. Plus you will need: 1 - 608 bearing 2 - M4 x 16mm bolt Instructions: 1) Lay the ring on a flat surface and press the bearing all the way in. 2) Push a spacer into each side...

At some point I was not satisfied with a filament spool holder of my Anycubic Mega S - it was too much friction there. So I did a quick design of a simple attachment based on conventional 608 bearings, which are cheap and are used everywhere -...

it's designed to work with the cheap and readily available MakerBot style End-stops. https://www.aliexpress.com/i/4000602284637.html Filament roller guide by @Calvin_MegaZero : https://www.thingiverse.com/thing:4626077 This design aligns perfectly...

Also, drilling into the sheet metal is involved for the Y axis. Mount screws are M5 and need sliding M5 nuts for the aluminum extrusion. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: .16-.20mm...

This is a simple extruder holder for the Anycubic Mega printer that fits snugly on the sides of its frame, securely in place without sliding up or down by itself while not obstructing the Z-axis carriage. The design's symmetrical nature allows it to...

Modified astroaaron's file a bit. ...Moved the top holes in a bit as they didn't quite line up on my Mega X. Added an arm to mount the filament sensor to so it could also guide the filament from a standalone spool holder a bit better.

... file a bit. ...Moved the top holes in a bit as they didn't quite line up on my Mega X. Added an arm to mount the filament sensor to so it could also guide the filament from a standalone spool holder a bit better. ... Category: 3D Printer Parts