anycubic i3 mega s firmware upgrade 3d models

So my first version flopped, mainly because I had to merge two pieces together (the original piece didn't fit Mega S, so I merged it with something else that could). Anyway, I remixed a more stable version using other parts. The stalk or stem, I...

Set of 2 Parts for Anycubic i3 Mega 3D Printer. The Heatbed Cable Holder and Y Carriage Holder. Print with Ease: No Screws or Joints Required. Simply Print and Snap into Place on the Heatbed as Designed and Enjoy. Check out the Complete Collection:...

I've attached the OpenSCad sources for easy customization because my Anycubic doesn't have a bottom enclosure, so the fan has enough room. ... It's an easy print, just turn it on the flat side and add support from printbed only (probably will print...

Altered the dimensions to better fit the frame of the Mega-S. Added a corner relief and a lead-in on either end for the frame corners. Infill doesn't seem to matter too much, especially if you add more walls. **UPDATE** It might be a bit too long...

Nobody sells this part that fits the new Mega-S Titan clone, so I had to remix it from scratch using other parts. Note, not shown in the picture: I added a bit of tubing for the inlet to make the filament flow extremely smoothly. Check out the...

Meine Version der Kabelführung für den Anycubic. Zwei Dateien stehen zur Auswahl, einmal für links und einmal für rechts. Viel Spaß damit. My version of the cable management for the Anycubic. There are two files to choose from, one for the left and...

A simple Spool Holder for the Anycubic. The Screws must be a bit longer than the original. The Carton Filament Spool will rotating more easily than the original Holder. it is also a bit wider. ... Need no Support

Jedynie co będziemy potrzebować to dwa łożyska RJ4JP-01-08 x2 (lub łożysko oryginalne z Anycubic) oraz Prowadnica liniowa średnica 8mm (długość minimum 400mm), 4 śruby M3x25. ...Proszę użyć orientacji jak na zdjęciu oraz opcji "drukuj płasko" nie wymaga...

There is also an upgrade from I3 Mega or Mega M to Mega S or S Pro: Anycubic Upgrade [Amazon EU/DE] But with the new extruder, you'll need a new firmware and/or have to adjust the E-steps and calibrate it. For this, you need to send the commands...

This cable fixation bracket provides a snug fit on the hotbed mount sub-plate, safeguarding soldered hotbed connections that are known to be problematic on Mega series printers. Installation: To install this bracket, I recommend removing the hotbed...

Here is a list of the parts I printed and additional stuff needed for the mod: Printed parts – Thank’s going to the designers of the parts mentioned below: carrier plate with Bltouch support and fan duct: https://www.thingiverse.com/thing:4299180...

It's a hotbed cable guide

To overcome these issues, you'll need to create new profiles for your printer and materials, making this upgrade far from plug-and-play. Use it only if you're experiencing overcooling issues. For optimal results, I recommend using stainless steel...

The tools holder mounts securely to the left-hand side of the printer's frame, which features a minimalist design.

I got a MOSFET Board with uncommon dimension, So I re-designed the whole. ... For MOSFET with 41.5mm x 51.5mm borehole. The design is inspired from Max3D-Druck's Mosfet Mount.

To better control the filament at Any, turn the extruder's mounting angle and attach this holder. A M3 threaded insert is required for the holder. The large depression can be used for a 14x4mm magnet, but it is not typically needed. ...Position the...

... light for standard LED strips. ...It's mounted on the hotend cooler fan and competely hidden inside the hotend (original or honeycomb) and compatible with the dual-side part cooler. ...LEDs can be connected to fan power or wire them to 12V of the PSU.

From the ground up, I revamped the project based on MakeNGrow's design, modifying the filament hole to accommodate an adapter specifically tailored for TPU filaments' flexible nature. ...Meanwhile, I strengthened the structural posts surrounding the...

I took inspiration from https://www.thingiverse.com/thing:3930311 and decided to make a few tweaks to ensure there's ample space between parts, so I modified the design to clip from the very top instead of relying on clearance alone. ...Unfortunately,...

I'm thrilled to share that I've created my very first piece using Cinema 4D, specifically designed for my 3D printer. ...I've utilized CURA's capabilities to precision-cut the design. ...I must say, I'm absolutely delighted with how it turned out!

Surprisingly, the mainboard's power consumption is very low when not driving the hotbed or hotend. As a result, you no longer need oversized wires. ... This holder fits seamlessly with the stepper driver fan duct and Noctua fans, which can be found on...

... and made room for my go-to pliers. The smallest hex key is a snug fit but it stays put. I also beefed up support between the attachment and the tray itself. You can never be too sure if it was needed, but it's always better to be safe than sorry.

We design a lock that secures your patio umbrella in place when tilted to block out the sun's intense rays. Crafted specifically for 37mm umbrella poles, this solution may also work on sizes ranging from 36-38 millimeters, although thorough testing...

If you've found this solution helpful, consider supporting the development of more innovative products like this one by donating what you think it's worth through our PayPal account. Your contribution will help offset the time and effort invested in...

I designed this magnet holder for the Raspberry Pi 3/4 touchscreen from "Phillip's 3D Print Shop" because I wanted to place the touchscreen without drilling anywhere on the frame. This is secured with a Neodym magnet glued into the holder and...

Teileliste: 1x Gehwegplatte aus Beton (400x400x50mm) 2x Gewindestange M8 L=170mm 6x Mutter M8 4x Scheibe für Schraube M8 2x Klemmelement_Betonplatte (STL zum ausdrucken) ->PLA oder PETG 2x Montageplatte_Drucker (STL zum ausdrucken) ->PLA oder PETG...

You have to pull the mainboard out of the case to install the fan upgrade for the fan duct into your printer, and it's a snug fit but it works.

A two-part clip-on holder for a digital caliper on the AnyCubic i3 Mega printer.

Here is a bed holder for the Anycubic I3 Mega or Mega S printer. Unfortunately, so far none of them fit correctly because they are too loose. ...To solve this problem, I designed and built my own version that fits perfectly and is easy to install...

Model for Calibrating the Print Bed on an Anycubic MEGA-S 3D Printer