anycubic i3 mega s 3d models

Trash bin for Anycubic i3 Mega S. (I don't know if it fits to Mega also, you can check the screw holes if it fits) No supports needed. ... I've printed the Base with %20 infill and the Box with %100 infill and 0.2 mm layers.

I wanted to install a 60mm LED ringlight on my Anycubic I3 Mega-S printer, so I built an adapter to match the existing screw holes. The Ledring attaches securely with adhesive, and you must connect wires to the second fan's electrical terminals. ...I...

Simple mounting plates are designed for the Anycubic i3 Mega S. These plates enable users to easily attach components to the spool holder and Z-axis. A total of two, four or six 6x2 magnets are required, which can be sourced from...

[999D](https://www.thingiverse.com/999d/) provided a nice replacement for the extruder lever of an Anycubic i3 Mega S: https://www.thingiverse.com/thing:4248053 This is a remix by cutting the model in half and glued it together afterwards. ...For easier...

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

Direct cable access requires modification to the Anycubic i3 Mega's casing. Specifically, the red, green, and black sockets located on the right-hand side need replacement with open-ended cable passages. ...This alteration allows for unimpeded cable...

... remix of https://www.thingiverse.com/thing:4193861 The original source is designed for 5015 fan and used for https://www.thingiverse.com/thing:3954252. ... In order to reuse Anycubic I3 MEGA-S original fan for direct extruder, mount was re-designed.

*While removing the filament in the Anycubic i3 mega s 3D printer, the tip of the filament gets stuck and it is difficult to come out. Thanks to this apparatus, you can easily remove the end of the filament by cutting it. WARNING: This apparatus is...

Modified the frame to fit perfectly around the Anycubic i3 Mega S, ensuring a precise margin and screen size. Mirrored the cover's design so that it can be mounted inside out, creating a seamless look even when the lid is closed - check out the...

I've built an adapter to make this case fit the Anycubic I3 Mega S. You'll need to remove the touchscreen for this to work. Note: This is currently a work in progress, and it's possible that it won't fit perfectly yet. ... Don't print it right now; I...

... ... Since I couldn't find a suitable filament sensor holder for the Anycubic i3 Mega-S sensor, I designed this one. The original sensor is positioned directly in the middle under the extruder and assists when the filament is drawn in from below (e.g.

Ein Halter für diese Thermometer https://www.amazon.de/gp/product/B07JDSHD4Z/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 an einem Anycubic I3 Mega (S/P) (beim X bin ich nicht sicher ob der Rahmen gleich breit ist) Das L-Teil muss mit Support...

https://www.amazon.co.uk/dp/B077HP7XX9 The holder is mounted to the SD card holder in the Anycubic i3 Mega-S Can be printed without any supports Print Settings Printer: Anycubic i3 Mega-S Rafts: No Supports: No Resolution: 0.2 Infill: 15%...

The purpose of this design is to allow the user to mount a camera on the back of the Anycubic i3 Mega S. The paddle-shaped design is mounted on the rear of the printer using two of the bolts used for stabilizing the rear servo for the print bed.

It's a nice bracket for the PiTFT to put it in place of the original display from the Anycubic i3 Mega S. I designed it as part of my upgrade from Marlin to Klipper. I don't know whether the bracket goes well with a normal Raspberry Pi. It works fine...

This handle fits perfectly on the Anycubic i3 Mega S printer's hot bed. Unfortunately, a previously printed bed handle here did not fit my printer's metal plate, which is a bit too thick at 3.5mm. Therefore, I suspect that the printer bed design has...

I've created an adapter to make this case fit on the Anycubic I3 Mega S. However, you'll need to remove the touchscreen for it to work properly. Please note that this project is currently a work in progress and may not be entirely accurate. It's...

After upgrading my Anycubic i3 Mega S (with new stepper drivers [2208] that had very large heat sinks), I didn't want to file the heat sinks down and i didn't want to buy another fan. ...I had just replaced the 50x10 with a new very quiet and high cfm...

Filament spool roller for Anycubic i3 Mega S. You need 2x 608ZZ bearings for the assembly. All parts are snapping together and no screws or glue needed. No supports needed. - I've printed the "Shaft" part vertical with a raft with %30...

For the Anycubic i3 Mega S, a Filament-Halter is required for easy unwinding. To install it, 2x M4 threaded inserts and 3-4 standard ball bearings (d1=22mm x d2=8mm x 7mm) are needed. The holes in the filament holder must be drilled to 4mm. A ball...

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

... aus und Schützt mein Riemenmotor. Drucker : Anycubic i3 Mega S Unterstützt : ja Füllung : 25% Anmerkungen : Stützstruktur : Tree und X/Y - Abstand der Stützstruktur auf 3mm einstellen !!! ... damit ihr die Stützstruktur ohne Probleme raus bekommt!

The Anycubic i3 Mega S requires an upgraded cooling solution, which involves replacing its bizarre stock driver board cooler with a more efficient one. This may necessitate re-seating the heatsinks, ensuring that their fins are perfectly parallel to...

The arm or lever on the extruder of my Anycubic i3 Mega S snapped and I was unable to manually load or unload filament by hand. It appears that the original is pretty fragile and will likely need to be replaced sooner rather than later. This upgrade...

Hey, I didn't find an easy way to set the Z-Axis screws on my Anycubic I3 Mega-S Printer, so i designed this simple distancer with different heights that can be used to align the X-Axis parallel to the Print bed. I determined the approximate...

I don't like the stock spool holder that comes with the Anycubic i3 Mega S as this one has to much friction. Looking on thingiverse I came across this: <a href="https://www.thingiverse.com/thing:4167075">design</a> from <a...

This is an alternative hotend housing for the Anycubic i3 Mega-S. It is mostly based on the silent hotend design by mileshkin but I removed the mounting location for the original parts cooler fan on the left side and put air vents on that side...

--------------------------------------------------------------------------------------------------------------------------- [IT] LA MIA GUIDA AGLI UPGRADES PER LA ANYCUBIC I3 MEGA-S Navigando in Internet ho trovato giusto la metà delle modifiche che...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...