anycubic i3 mega x 3d models

2 x M3 screws x 20mm 2 x M3 Nuts 2 x M3 screws x 6mm...

You'll need: -one 12mm diameter pulley with a 3mm diameter bore bearing for GT2 timing belt, width 6mm, -one M3 nut, -one screw, M3 x 16mm, -two screws, M3 x 8mm, -three M3 washers. Put the nut into its designated hole. Next, place two of the M3...

2 6mm x 455mm rods 1 6mm x 388mm rod 6 8x3mm magnets (I use four more to close the enclosure) I've used a large trash bag and duct tape to create the enclosure, with the front panel separate for now since I don't have transparent plastic. You can try...

... fit on the opposite stepper motor. After installing the stepper motor, I noticed that the bolts used to secure it were slightly too short (M3 x 5mm). ...To compensate, I replaced them with M3 x 8mm bolts, which provided a snug fit for the guard.

For Reference, My K8200 Printer's Decibel Levels Are: dBA at 100% fan speed: 38 (average), 48 (peak) If You're Interested in Creating Your Own Custom Hotend Cover, Here is the BOM for This Project: 4 x M3x20 Screws (for fans and front plate) 2 x...

You will need two M3 x 12mm hex screws, two washers, two nuts to keep the clamp in place. Note that the clamp does not tighten it to the frame, but more a holder to keep it from coming off of the frame. ...The nut was made with the threads only half way...

I discovered that the bolts used to secure the stepper motor are slightly too short (M3 x 5mm), so I opted for M3 x 8mm bolts to get this guard to fit properly. The LED strip visible can be purchased here: an LED strip When mounting it, use multiple...

This overhauled hotend housing allows you to see the printhead easily, allows for adequate cooling of the heat sink, hides all of the wires by moving the plugboard behind the x-carriage, and also has a modular part cooling duct that can be changed if...

You can scale up the X axis, which will make it longer. In my case, I designed it with a 10cm length, and that seems sufficient. The curved side may not look great, but it functions well and remains out of sight on the printer. I hope you enjoy...

... hold. A dual-bearing setup is employed on the X-axis carriage. ... Update March 12, 2018: A revised v2 version of the Igus double holder has been added, along with a flat variant without the strips, suitable for use with Igus RJZM-02-08 bearings.

I found that the bolts that are used to secure the stepper motor are just a bit too short (M3 x 5mm), thus I used some M3 x 8mm to get this guard to fit. The ledstrip you see can be bought here (affiliate): LED strip I mounted it using multiple of...

https://www.amazon.com/gp/product/B07K2Y9XSH/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 You will also need Seven M3 x 10mm long SHCS, and four M3 x 35mm long SHCS: https://www.mcmaster.com/91292A113/ https://www.mcmaster.com/91292A033/ There...

I discovered that the bolts used to secure the stepper motor are slightly too short (M3 x 5mm), so I substituted M3 x 8mm bolts to get this guard to fit snugly. The LED strip visible in the image can be purchased here: https://bit.ly/2HfgdhQ I...

This upgraded hotend housing lets you see the printhead easily, enables adequate cooling of the heat sink, conceals all wires by moving the plugboard behind the x-carriage, and also features a modular part cooling duct that can be changed if you...

I'm using two Noctua 40mm x 10mm fans to cool the hotend and the printed part, which requires low airflow so I redirect and funnel the output to the nozzle's end and it seems to be enough. You don't need to adjust the hotend angle or change the...

I did install the upgrade kit for the I3 Mega (TITAN-Extruder and Filament-Rack) - the kit is really worth checking out: https://www.amazon.com/gp/product/B07KLJJYNV/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1 But the filament holder falls...

I tried to find a spool holder for my i3 mega but did not end up with one that worked as I wanted, so here we are again and designed one that was more suited for what I need. So I wanted a roller model and after the first few prototypes, I ended up...

After swapping out the fans on my i3 Mega, I decided to tackle other sources of noise as well. The result is my Silent Filament Guide, expertly paired with my Spool Holder. Thanks to the PTFE tube inside its housing, it won't generate unpleasant...

I used a previous chain design as inspiration; I believe it was this one: http://www.thingiverse.com/thing:1735193 Print Settings: Printer: Anycubic Mega i3 & Omega i3 Rafts: No Supports: Yes Resolution: 0.2 or 0.3mm Infill: 20 or 30% Notes:...

He canviat la mida del suport per adaptar-lo a la ANYCUBIC MEGA X

Modified version of mjuddi's design, adapted to fit the tools accompanying the Anycubic Mega X.

Adapter to fit HugoHuge's Customizable Filament Holder onto an Anycubic Mega X.

I'm using it on my custom Anycubic I3 Mega, but it should work on all types of Prusa printers with this mount: https://www.thingiverse.com/thing:926794. The fan duct isn't ideal, but it works. Unfortunately, it's not as good as the stock one. If I'm...

Filament spool holder for Anycubic Mega S and Mega X. 2 ball bearings 16x5x5mm and a shaft 5x94mm. To attach to the existing holder. ...Spoolholder hole diameter ≥ 52mm

Filament spool holder for Anycubic Mega S and Mega X. 2 ball bearings 16x5x5mm and a shaft 5x94mm. To attach to the existing holder. ...Spoolholder hole diameter ≥ 52mm

This is a set of reinforcement braces for the u crossover and gantry on the Anycubic Mega X. It'll probably work on the other anycubic I3's as well but I dont have one of the smaller ones to test. ... Printed it in petg with 100% infill no supports, I...

Ein Griff für den Anycubic Mega X um das Druckbett beim leveln besser bewegen zu können. Ich habe etwas doppelseitiges Klebeband in die Lasche geklebt, damit es gut hält. Funktioniert prima. A handle for the Anycubic Mega X to move the heatbed...

Cable management for Mega X

Dust cover for Anycubic Mega X When working on the Y-axis, open the rail covers at both ends of the front and back, install the dust cover, and then reassemble.

Made a simple mount for a ESP32 camera for my Anycubic Mega X. The ones I found did not fit the Mega X, as they where designed for the smaller printer line. I printed it with out support. It's supposed to be mounted at the front of the...