anycubic i3 mega x 3d models

This is a nozzle rack that I designed for my Anycubic I3 Mega S. I imagine it will also fit other similar models. This one sits on the left hand side of the printer and mounts using the vent holes. Prior to this one I made a nozzle rack that clips on...

This is a modified version of "Anycubic I3 Mega Hotend Cover with LED Bar" by jboehe, featuring reinforced top edges. The original design's side walls were 2.11mm and 1.89mm thick, but with a 0.4mm nozzle, the thinner wall would print hollow and warp...

This is a PSU cover for Anycubic i3 Mega to replace the default fan with a 100x15mm fan. It appeared to be a tight fit, with only a millimeter clearance from the induction coil. I added corner support and mounted the fan using the bundled screws. To...

anycubic i3 mega printhead cooling for 40x40 fan set separated in 5 parts for easy printing : 2 parts for wire cooling (assembled by fitting + fan screw + 1 screw/accessory bolt) 2 parts for the cooling of the printhead body ( assembled by fitting +...

Anycubic I3 Mega Fanduct Rear Mounted for Radial Fan Get the UEETEK 12V Heatsink (https://www.amazon.de/UEETEK-Drucker-Heizk%C3%B6rper-Ausgezeichnet-K%C3%BChlk%C3%B6rper/dp/B06XCSPVC8/ref=sr_1_3?ie=UTF8&qid=1514808721&sr=8-3&keywords=ueetek+12v) for...

Hotend Housing for Anycubic i3 Mega. First, apologies for my poor English. The Original Hotend Cooler Doesn't Fit; an External Fan Duct Must Be Used! https://www.thingiverse.com/thing:3116153 Print Settings: * 100% Filling * No Support * Printed...

I designed this flexible coupling specifically for the Anycubic i3 mega to connect threaded rods and Z-motors because of z-wobble issues. Replacing rigid couplers with these flexible ones compensates for imperfections in threaded rods. To attach...

Just another fan duct for the Anycubic i3 Mega. I didn´t like the ones i found on thingiverse because they neither fit on a 5015 radial fan nor have enough space between the fan duct and the build plate nor they couldn´t get fixed on the hotend...

This design is tailored for AnyCubic I3 Mega ultrabed owners only. The head mount was adapted from another project. To assemble the holder, you'll need to provide support for the head mount section. Instead of using the head mount cover, simply...

My Anycubic i3 came with a neat USB SD card adapter. ...To keep it close to my printer I created a simple mount for it.

Abdeckung für das aktuelle Netzteil des Anycubic i 3 Mega S. ... Es sollte die Stützstruktur aktiviert sein, jedoch sollte für den gesamten Berech, bis auf die eine Befestigung ein blocker erstellt werden (siehe Foto).

This is a Mount Plate designed specifically for the Anycubic Mega 3. ... This is still a base plate engineered for Raspberry Pis equipped with cooling cases to securely mount them.

Until then, I'm just going to post this stuff separately in case someone can make use of it.I bought a cheap MK8 extruder designed for a CR-10 from Amazon, and I used these pieces to mount it to the left side of my Anycubic i3 Mega-S. I've included...

Anycubic I3 Mega Head Cover and Cooling Upgrade. !!! Updated Version Here: https://www.thingiverse.com/thing:4236578. Metal V5 Head Cover and One-Side Cooling on Mega Has Some Problems. Many Tries to Solve It with Custom Covers, But None of Them...

It seemed like the power supply was glitching out on my Anycubic i3 Mega S, so I ended up replacing it with the MeanWell LRS-350. I used the power supply cover from Zcubed, the first picture one, and made a mount that makes this thing fit within the...

This is an adaption of my Sovol SV01 board fan holder for the Anycubic i3 Mega and Mega S. It consists of two parts: a baseplate which is mounted on the SDCard reader brackets and with the screw holes of the original holder. The base plate also...

It seemed like the power supply was glitching out on my Anycubic i3 Mega S, so I ended up replacing it with the MeanWell LRS-350. I used the power supply cover from Zcubed, the first picture one, and made a mount that makes this thing fit within the...

Raspberry pi 3 b+ holder for Anycubic MEGA X

I placed my Anycubic i3 Mega inside an IKEA housing, specifically the STUVA cabinet with a SINDVIK glass door. The cabinet is spacious enough, but once the printer is installed, there's limited room for the spool and its holder. The original spool...

Anycubic i3 Mega S Y-Carriage Belt Tensioner UPDATE: Added a Carriage_mk2 file which features a slightly sturdier back. I noticed after a year of use and perhaps slight over-tensioning on my part, the screw that pulls the carriage back has started...

The screwholes allow for some up- and down adjustment to get the perfect height above the part. For mounting the fan to the duct a m3x25 screw and an m3 nut are requried. To mount the fanduct the hotend has to be rotated by 90 degrees so that the...

Skip everything and start: main links you need: https://github.com/luc-github/ESP3D https://github.com/luc-github/ESP3D-WEBUI (get v2.1 or higher) PDF guide in this thing with some specifics for ESP12e wifi board Slow version: I really wanted to...

This is a flexible coupling I designed for the Anycubic i3 mega to connect the threaded rods and the z-motors, because I had some issues with z-wobble. I replaced the rigid couplers with these ones, to compensate imperfections of the threaded...

... These are unmodified copies from the original makers. Print SettingsPrinter:Anycubic i3 Mega Rafts: Doesn't MatterSupports: Doesn't Matter Resolution: 0.2Infill: 20%  Category: 3D Printer Accessories

Hi, I've got an i3 Mega UltraBase with TMC2208 drivers, and I designed a duct for it over on Thingiverse - https://www.thingiverse.com/thing:2773533. It worked okay until I upgraded to Marlin 1.1.8. With the new firmware, I was able to hit higher...

This spool holder should bolt right onto the I3 Mega Gantry, If it also suitable if you have another mount currently on the gantry, for example, a gantry extruder mount. I could only find a single AnyCubic front facing spool gantry holder suitable...

This design should fit Anycubic i3 Mega and Mega S printers. However, it's crucial to note that it's not compatible with the latest version of the board featuring an integrated SD card reader and fixed motor drivers. Initially, I thought I could...

I've been working on a design for the BL Touch that attaches to the existing hot end carriage of the I3 Mega with minimal modifications required. Two distinct designs have been created, each offering a unique approach to incorporating the sensor into...

Anycubic I3 Mega for IGUS bearings RJ4JP-03-08 remove the O-Rings! 4x M4 hex nuts / bearing support Igus Bearing: ...

I made this dual sided fan duct as a slightly improved / better fitting version of the original dual-side fan duct made by H_Run. The original one had some fitment issues on my printer (the fan shroud was too big and too far up). I also changed it...