anycubic i3 mega z axis adjustment 3d models

... isn't as steady as you'd like, a simple solution may be just what you need. ...First, place a circular bubble level in the center of the work surface. Next, adjust the 30mm ball or foot by rotating it until the level indicates perfect equilibrium.

The Anycubic on Boot talks to the wifi module with AT commands at 115200bps, sends an AT command to switch at 2.250.000Bps and opens UDP server in port 3000. This is a sniff traffic on port, commands sent from Printer. Boot printer and it sends at...

I decided to re-create the holder because I wanted to build it myself in Fusion360 and I needed both ends to be movable so I could adjust the spool on its shaft slightly. What you will need: 1) Two pieces of 608 bearings 2) An 8mm rod - 15cm long ...

I've made some adjustments to the file to ensure the holes and washers fit snugly, eliminating any tight spots. To print this model, use PLA with a bed temperature of 190c and an extruder temperature of 60c. Note that I initially started the first...

... Remove the screws from the stepper motor. Place the assembled pulley in its designated position and secure it using the two M3 x 8mm screws. Adjust the belt tension as desired and lock the screws in place. ... Freecad sources are included.

You don't need to adjust the hotend angle or change the original bolts; you'll just need four M3 nuts to attach it to the carriage. You'll also need twenty millimeter M3 bolts and nuts to secure both fans, but if you don't use fan covers, sixteen...

I found this design to be satisfactory on half-spools but needed some adjustment when the spool was full. To improve this, I extended the length by 20mm and uploaded version v5, also adding more depth to the hole for the PTFE tube. Initially, I...

X-gantry ZX Fox 50mm https://www.thingiverse.com/thing:4352064 X-carriage MT2 Direct Drive - Bondtech BMG https://www.thingiverse.com/thing:3680044 Remixed chain from https://www.thingiverse.com/thing:3668667 ITALIANO Ho personalizzato e modificato...

X-gantry ZX Fox 50mm https://www.thingiverse.com/thing:4352064 X-carriage MT2 Direct Drive - Bondtech BMG https://www.thingiverse.com/thing:3680044 Remixed chain from https://www.thingiverse.com/thing:3668667 ITALIANO Ho personalizzato e modificato...

I did install the upgrade kit for the I3 Mega (TITAN-Extruder and Filament-Rack) - the kit is really worth checking out: https://www.amazon.com/gp/product/B07KLJJYNV/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1 But the filament holder falls...

Kleiner Halterwinkel zur Führung der Z-Spindel. ...Verwendetes Lager 608 22x7x8mm

I tried to find a spool holder for my i3 mega but did not end up with one that worked as I wanted, so here we are again and designed one that was more suited for what I need. So I wanted a roller model and after the first few prototypes, I ended up...

Friction-fit fan mount with air channels and clearance for a 40mm heat sink attached to the end of the Z-axis stepper comes with mounting holes designed specifically for a 40mm fan. Printing it with the mount side facing down is recommended, as...

After swapping out the fans on my i3 Mega, I decided to tackle other sources of noise as well. The result is my Silent Filament Guide, expertly paired with my Spool Holder. Thanks to the PTFE tube inside its housing, it won't generate unpleasant...

I'm using it on my custom Anycubic I3 Mega, but it should work on all types of Prusa printers with this mount: https://www.thingiverse.com/thing:926794. The fan duct isn't ideal, but it works. Unfortunately, it's not as good as the stock one. If I'm...

Hey there!\r\n\r\nI've designed this simple yet robust tensioner. It's a great solution for any project that requires a reliable and easy-to-use component. Here are the printable parts you'll need to assemble it:\r\n- Base plate\r\n- Nut\r\n- Pulley...

This component replaces the fixing belt end part situated beneath the tray. It is a compact tensioner part that performs efficiently. When tightening the belt end, it's advisable to loosen the tray support screws for smooth operation. ... The bill of...

Remixed the original design by molnija3d which was not tall enough to fit the pulley. ...This will fit beneath the build plate without issues.

I loved the original pulley cover, but after a while it would always turn slightly out of alignment and the belt would start scraping against the wall of the cover. And why shouldn't there be a cover for the pulley of the stepper motor? ...So I took 5...

I replaced the z end stop with an adjustable one, utilizing the stock holder and two M3 bolts that came with the kit, along with an M4 x 25 bolt and two M4 nuts. I based this design on the model found at https://www.thingiverse.com/thing:1727889. A...

I designed this mount to secure the camera along the Z-axis, allowing for clear visibility of the nozzle even on high-pressure parts. ... To get started, simply follow this link for a compatible chain set including mounts: ...

LERDGE Z 2.0 SCREEN i3M mount Für das "Loch" und die Schraubbefestigung des Original Screens Bilder folgen noch....

Based on derLowy's design, this cable guide allows for maximum printable z-height since the cable passes to the left of the bracket instead of above so it doesn't interfere with the top of the gantry. To squeeze out a couple more millimeters the...

Based on derLowy's design, this cable guide maximizes printable z-height since the cable passes to the left of the bracket rather than above, thereby avoiding interference with the top of the gantry. To gain a couple more millimeters, the cable can...

To print high Z-height parts without crushing the Bowden tube beneath the frame, I adapted astroaaron's design (https://www.thingiverse.com/thing:2854805). The hotend cable guide on the right was switched and a guide for the Bowden tube was added. A...

However, I also needed a Z-shield spacer. So, I created this remix of both products. You can use five of the original parts for the strip and one of my modified components. Since I wasn't satisfied with the solution that involved a cable tie, I...

The one shown in photos is "z-wob_25distance_225bearing_2screw_m3.stl". I have installed it using a couple of M3 button hex screws, washers and locknuts and it works perfectly. Printed using PETG and I recommend you do the same as PLA may be too...

Here is the rewritten text: EndStop Adapter Check out this high-quality mechanical EndStop for Reprap ramps 1.4 and 3D printers at...

Using a Drag Chain Measuring 10x20mm. Important Note: Cables Must Be Extended. ... The Upper End Holder Is Provided By Michelix, Where An Additional Holder For The End Of The Chain Link Has Been Added As Well.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...