anycubic mega pro leveling 3d models

Ersatz für die Standard-Einstellraeder des Mega Pro.Die Skala erlaubt das einfache Einstellen bei der Verwendung unterschiedlich dicker Druckplatten auf einem magnetischen Heizbett (Steigung vom M3-Gewinde ist 0.5, d.h. eine volle Umdrehung...

Ersatz für die Standard-Einstellraeder des Mega Pro. Die Skala erlaubt das einfache Einstellen bei der Verwendung unterschiedlich dicker Druckplatten auf einem magnetischen Heizbett (Steigung vom M3-Gewinde ist 0.5, d.h. eine volle Umdrehung...

A mount that fits onto the AnyCubic Mega Pro (and printers in the same AnyCubic family). It lets you install a digital tire depth gauge of the type commonly sold on Ebay, AliExpress, etc. Gives you another option for bed leveling. Print it on its...

Hey there, this is a clamp for the ultrabase on my anycubic mega pro. I think this can help to "remember" how high or low you bed is. ... This is fine if you are not working with mesh leveling, to standard a height to handle troubles better when it...

a handle specially designed for the anycubic mega pro for leveling the printing plate

Leveling knob for the Anycubic i3 Mega. Just slip them on until they bottom out on the existing leveling nut. Makes it so much easier to level the bed especially the back of the print bed. NOTE: As shown in the picture, this is for the brass style...

If your table is a warped as mine this might help. ...I put a circular level in the middle of the plate and then I can rotate the 30mm jack or base to level the machine.

An simple shape to help level your bed, will go in a squire pattern around the edge of your print-bed

The Anycubic Mega Pro Levelholder! After leveling of the bed you can click the level holder onto the leveling wheels. There will not by any changes in the bed level any more. ...This protected especially at the wheels in the back where the cables may...

This is a part test to show the correct leveling of the Anycubic I3 Mega Printer.

actually a remix of : https://www.thingiverse.com/thing:3791392 And https://www.thingiverse.com/thing:4178350 Anycubic mega S leveling know, with Up arrows.

I decided to design these leveling wheels for the hot bed of the anycubic I3 Mega, of a large size to facilitate leveling, although it may be compatible with other printers, it must be borne in mind that they are very large and that even in anycubic...

A leveling wheel cover for the Anycubic Mega S. Smaller than many designs to miss the cables in the right rear of the machine. Press on fit. ... Prints flat with no supports.

A leveling wheel cover for the Anycubic Mega S. Smaller than many designs to miss the cables in the right rear of the machine. Press on fit. ... Prints flat with no supports.

... *** *********************************************************************************************** This is a remix of MKingCharles Bed Leveling Knob "Tire" for Anycubic i3 Mega by MKingCharles Oct 9, 2018 https://www.thingiverse.com/thing:3145976

This is a redesign from scratch of MKingCharles "Bed Leveling Knob "Tire" for Anycubic i3 Mega" with knurling on the outside. ... I found adding a brim helps because the bed adhesion around the holes has such a small area that it was warping.

### CREATED for the ANYCUBIC MEGA PRO version equipped with a LASER. * This cable support was originally created by [Alex100dre](https://www.thingiverse.com/thing:2186997) for the Anycubic i3 Mega. > Prevents the cable from over flexing and...

Schleppkettenhalter für den Anycubic Mega Pro ergänzend zu https://www.thingiverse.com/thing:2860786/files Cablechain holder for the Anycubic Mega Pro in addition to https://www.thingiverse.com/thing:2860786/files

Drag chain holder for Anycubic i3 Mega Pro. The i3 Mega Pro has a different extruder than the i3 Mega. I created a suitable holder for it. ... The other part is here https://www.thingiverse.com/thing:2860786

Assisted Bed Leveling GCODE for the Anycubic I3 Mega This code moves the printhead automatically to 4 corners in total 4 times which should be enough to level the bed. If you need more iterations just copy and paste the code from one round. ... If you...

So, I came to the realisation after doing a print and having it fail that some of the levelling knobs on my Anycubic I3 Mega had come off. The issue with this is that they were nowhere to be seen. So I designed a knob replacement that has thread...

Remix of https://www.thingiverse.com/thing:3520264 to fit Anycubic Mega Pro or any printer with 20mm diameter round feet.

There are many bed leveling knobs or knurled nuts for the Anycubic. Surprise! Now i have one more for thingiverse! :-) But what i haven´t found on thingiverse solving my problem was this: Because I was really annoyed that I had to level all the time,...

The Anycubic Mega Pro has a different PSU than the rest of the mega series. There were no PSU covers on here, so I designed my own. This fits a 92x14mm fan. ... I used this one from Noctua https://www.amazon.com/gp/product/B07ZP6KKKZ ...

A model for leveling the bed of Anycubic MEGA-S (i3 Mega).

A model for leveling the bed of Anycubic MEGA-S (i3 Mega).

Drag chain holder for Anycubic i3 Mega Pro.The i3 Mega Pro has a different extruder than the i3 Mega.I created a suitable holder for it.You can find the other parts herehttps://www.thingiverse.com/thing:2860786Print SettingsRafts:Doesn't...

### Bed Leveling Knob. ... I was looking for a handle for leveling the table, everything that I met for various reasons did not suit me, I decided to model it myself. ...

This wedge is used to perfectly level the base in the center if it is concave. You need a 4x50 screw and an M4 bolt. ... In order not to directly touch the wedge with the resistances of the base, it is necessary to place a felt or an insulating piece...

*Disclaimer I have not tested this version.* This is a remix for Anycubic Mega Pro as requested by user: TheApprentic3 . Main body width is shrunk to 219mm, bottom panel, left body, and right body is also updated to make it fit. The case internal...