anycubic mega s fan upgrade 3d models

Fan cooler Upgrade puts the nozzle closer to the work being printed.

IMPORTANT: Use 5V fan in the hotend (tested) The change in this Remix was the I3 Mega for Mega S and other no named With this fan mod you can use two 40x40x10 fans Update Experimental BL Touch ( No Tested ) Plz Give me Feedbacks Update 22/11/20 BL...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

--------------------------------------------------------------------------------------------------------------------------- [IT] LA MIA GUIDA AGLI UPGRADES PER LA ANYCUBIC I3 MEGA-S Navigando in Internet ho trovato giusto la metà delle modifiche che...

I couldn't find a good fit version for my newest Anycubic Mega-S so I made one myself! ...Keeping it small and light with an open front to still be able to see what is going on (with my DIY led holder) but far away from the nozzle.

(same problem with the most other fan ducts) The standard fan comes with two little tubes, acting as spacers, to assure there is a gap between the fan an the housing. To mount the fan/fan duct that way, without removing any other parts, is really...

Upgrade for extruder

i made this in the free to use fusion 360, it is an upgrade for holding the wire harness and filament tube on the top of the hot end. ...assembled using zip ties

this kit includes everything you need to upgrade your i3megaS from stock to upgraded :)i hope you enjoy it ;)THIS KIT INCLUDES:1-Bed leveling knobs2-Cable clip for hotend cables3-Stepper motor covers4-Sd card grip5-Dinkelmeme Logo plate6-Filament...

**1) Optical improvements** + Making the front panel a bit more beautiful with a simple (!) frame https://www.thingiverse.com/thing:2758459 + Hide front pulley https://www.thingiverse.com/thing:2837666 + Hide rear pulley...

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

I have the Anycubic M (Anycubic I3 Mega) from 2018 with replaceable drivers: [Anycubic M](https://amzn.to/2NTFT50 "https://amzn.to/2NTFT50") [Amazon EU/DE] [Anycubic i3 Mega](https://amzn.to/2HoAP7A "https://amzn.to/2HoAP7A") [Amazon US] But there...

Fan Holder for Anycubic I3 Mega S

Anycubic Mega S - Circular Fan Duct. ... Can be printed without supports.

After upgrading my Anycubic i3 Mega S (with new stepper drivers [2208] that had very large heat sinks), I didn't want to file the heat sinks down and i didn't want to buy another fan. ...I had just replaced the 50x10 with a new very quiet and high cfm...

Cooling fan airduct for Anycubic i3 Mega S, to upgrade its original bizarre driver board cooling solution. You may need to re-seat heatsinks, take care to put the fins parallel to the airflow. The STL file is for 9x10x12mm heatsinks, with 1mm...

Direktextruder Anycubic i3 Mega S you also need a set of screws: - 4x m3x28 - 2x m3x20 - 2x m3x25 - 6x m3x9 this kit only works with the fan holder designed by me it can be downloaded under my profile;)

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

AnyCubic i3 Mega S Fan Duct for 5015 radial fan. My Fan:...

You have to take the mainboard out of the case to get the mainboard and the fan holder into your printer, it's a little bit tight but it fits. ;) Du musst das Mainboard aus dem Gehäuse nehmen, um das Mainboard und den Lüfterhalter in den Drucker...

**UPDATE** June 30, 2021 -Added Fan_Suport_90x15_A_V2-tighter_nut_fit.stl **Recommended** **Anycubic Mega/S Motherboard Fan Mount 9015** Accommodates a 90x90x15mm fan. The centres of the 2 fan holes are exactly 80.15 mm apart. Fits perfectly inside...

Hotend fan duct to fit with the original Anycubic i3 Mega hotend. ... I used the screws provided by Noctua with the NF-A4x20 FLX fan to fix it with the duct: I changed a little bit the original .scad file to better clamp the hotend.

UPDATE June 30, 2021 -Added Fan_Suport_90x15_A_V2-tighter_nut_fit.stlRecommended Anycubic Mega/S Motherboard Fan Mount 9015 Accommodates a 90x90x15mm fan. The centres of the 2 fan holes are exactly 80.15 mm apart. Fits perfectly inside my Mega S. You...

Modified to make it easier to install on Anycubic i3 Mega S Configuration in CUra: Layer height: 0.2mm Initial layer line width: 100% Wall thickness, and upper and lower bases: 1.2 mm Fill: 50% Printing temperature: 200 C Hot bed temperature: 60 C...

I tried another fanduct but it didn't fit my i3 Mega - S fan so I decided to build my own. I also realised that most of the other fanducts are to close to the nozzle which can result in a burnt fanduct. ...That's the reason why I centered the fanduct to...

I attached the OpenSCad sources for easy customization (my Anycubic doesnt have a bottom enclosure, so the fan has enough room. It's an easy print. ...Just turn it on the flat side and add support from printbed only (probably will print without...

The total overall height of this bracket is 44mm vs the 42mm one that came with my Mega S. You will have have clearance issue with the heatsinks that come with the TMC2208 driver boards. This part will not solve that problem as the total depth of...

... es 16mm. Ich habe TMC2208 und die originalen Anycubic Kühlkörper. For 80x80x15mm fan, fits perfect. Screws M3x20mm IMPORTANT: Please measure first. From the board to the holder it is 16mm. ...I have TMC2208 and the original Anycubic heatsinks.

Anycubic I3 Mega S need: some screws and nuts 4020 fan Material: PETG/PLA type: Plug and play from original printer set