anycubic mega s octoprint 3d models

A convenient GoPro mount is designed to fit the Anycubic Mega S, also compatible with the Anycubic I3 Mega. This mount simply clips into place under the heated bed, allowing for adjustable height and camera movement. ... To create this mount, you'll...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

--------------------------------------------------------------------------------------------------------------------------- [IT] LA MIA GUIDA AGLI UPGRADES PER LA ANYCUBIC I3 MEGA-S Navigando in Internet ho trovato giusto la metà delle modifiche che...

My updated cable clip is a reworked version of tom666's original design, optimized specifically for use with the Anycubic Mega-S. ...It provides enhanced cable protection to prevent damage and ensure a secure connection.

Kabelhalter für den Anycubic i3 mega und mega s. wird einfach in den Schlitten vom Bett eingeklipst. der Deckel wird in die Grundplatte eingeclipst. Drucken unbedingt mit brim und supports. durch die kleinen filegranen Teile wird es sonst nichts...

SD card Face Anycubic Mega S. Supports for the board SD about 12 mm. The slot is made with a drill and bored. ...The caps and the board are slightly sharpened at an angle.

I printed this because the spools seemed to have more than desired friction on the anycubic mega s spool holder. Simply put it on top of the existing spool holder. I used 3M doublesided adhesive tape. ... Enjoy

A leveling wheel cover for the Anycubic Mega S. Smaller than many designs to miss the cables in the right rear of the machine. Press on fit. ... Prints flat with no supports.

This is a filament spool holder prototype for the Anycubic I3 Mega / s. ... -better printing result -relief for the engine Not perfect but it works bearing you need: 22x9,5x6 (turn Teil1 90* Teil2 180* Teil3 180*)

This is a filament spool holder prototype for the Anycubic I3 Mega / s. ... -better printing result -relief for the engine Not perfect but it works bearing you need: 22x9,5x6

80 mm led ring mod for the Anycubic i3 Mega S mit a Fan duct mod Inspired by: https://www.thingiverse.com/thing:2919948 and https://www.thingiverse.com/thing:2503909

A simple cable clip to tidy up the cables for a Raspberry Pi mounted on Anycubic Mega S. ... Remixed from https://www.thingiverse.com/thing:4693065 and https://www.thingiverse.com/thing:4196202 https://www.tinkercad.com/things/8BBsbRobnZ0

I made a DTI measuring gauge to fit on the original Anycubic Mega S. Got the Gauge from Aliexpress. ... Please use instructions on how to use it from https://www.thingiverse.com/thing:2469518 Printed without supports.

Quick solution to prevent the Eryone Filament spools from slipping off-center on the Anycubic Mega-S spool holder, ensuring they align perfectly with the sensor at all times.

Anycubic i3 mega s z-axis. ... You need: lm8uu bearings - 4 brass inset nuts M3 X D5.0 X L5.5 brass inset nuts M3 X D5.0 X L4 linear shaft 8mm 360mm and more length - 2

A leveling wheel cover for the Anycubic Mega S. Smaller than many designs to miss the cables in the right rear of the machine. Press on fit. ... Prints flat with no supports.

Direktextruder Anycubic i3 Mega S you also need a set of screws: - 4x m3x28 - 2x m3x20 - 2x m3x25 - 6x m3x9 this kit only works with the fan holder designed by me it can be downloaded under my profile;)

ANYCUBIC i3 MEGA-SJust something I made when learning fusion 360

Anycubic Mega 3D Printer is equipped with an i3 LED Light System.

Führung für Filament mit externem Filamenthalter. ... Geeignet für Anycubic i3 Mega Viel Spaß damit :D

... will be eliminated. It is compatible with all kinds of filament spools. Good prints ... Click the link below to see the new spool holder design for the Anycubic i3 Mega S. ...https://cults3d.com/en/3d-model/tool/anycubic-i3-mega-s-spool-holder-v2

... to fit the Quimat QY08-2 mosfets that can be found on Amazon (they are also sold under other names). https://www.amazon.co.uk/dp/B077HP7XX9 The holder is mounted to the SD card holder in the Anycubic i3 Mega-S Can be printed without any supports

### Credits - [Anycubic i3 Mega X carriage and Hemera mod](https://www.thingiverse.com/thing:4238185) by Sergiu-I - [BLTouch support](https://www.thingiverse.com/thing:4167435) by OmNomNomagon - ["Filler" filament spool...

Here is the rewritten text: This is a cover designed specifically for the zero position sensor of the Anycubic Mega S and i3 Mega 3D printers. The wires are now safely protected =) Some users have reported that this design does not fit the newer 2020...

Trash bin for Anycubic i3 Mega S. (I don't know if it fits to Mega also, you can check the screw holes if it fits) No supports needed. ... I've printed the Base with %20 infill and the Box with %100 infill and 0.2 mm layers.

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

For those of you who removed the annoyingly unreliable filament-out sensor on your Anycubic i3 Mega or Mega S. Use this filament guide in place of the sensor assembly. ...You will need to cut a piece of plastic tubing (I used the PET tubing from a pen...

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

Slim and easy-to-print brackets for LED strips are available for the Anycubic Mega-S, likely also suitable for i3 Mega.\r\n\r\nTwo pieces of side brackets and one piece of top brackets are needed (split in half due to print size).\r\n\r\nFits an 8 mm...

This is a lighting system designed for the Anycubic Mega S and Mega Pro. I used glue to attach the four towers to their bases. All other parts are just joined together using the plates. The led strip is 10mm wide. ...Larger strips may not adhere...