anycubic mega x calibration 3d models
376910 3d models found related to anycubic mega x calibration.
thingiverse
Cover to close the Voltage Selection Switch. I had to make it little smaller to fit into my printer. ... This is a remix from https://www.thingiverse.com/thing:2538654
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
During replacement of bowden tube on my printer I figure out that I could reduce it's size almost twice. ...Just with this simple upgrade you will be able to have 2mm of retraction settings.Youtube: https://youtu.be/DRXus4slqecUpdate:v1 - added corner...
thingiverse
Watch this YouTube video: https://www.youtube.com/watch?v=VnBOij_TeiM Then check out this other YouTube video: https://www.youtube.com/watch?v=68GY_8Auvw0 The build mainly employs M3 screws taken from stock printer parts, along with some M3 nuts...
thingiverse
Deleted the angel of the brace designed by leerm8680, because the Fiberlogy spools seeded to fall of during printing. ... Needed: 2x M3-nuts and the srews of the original MegaX filament holder
thingiverse
This is not a real remix of thing: 3064670 or thing: 2318068 Many thanks to tom666 and derLowy for their work. I redesigned both parts. The holder on the stepper motor is attached with three Neodyn magnets. It is best to pass the cable tie...
thingiverse
For best result, print it with 100% infill Dont recommend print by PLA. Why? ...Can print and find out why after 1-2 printings :))
cults3d
Deleted the angel of the brace designed by leerm8680, because the Fiberlogy spools seeded to fall of during printing. ... Needed: 2x M3-nuts and the srews of the original MegaX filament holder
thingiverse
**I should immediately warn you that this is a risky modification, and if you are not confident in yourself, then you should not improve anything!** I think this is my last attempt to improve this printer =) As the name probably implies, this is a...
thingiverse
A selfmade Adapterplate for the Zimpure fume extractor. I made it with Tinkercad. This is my first design - doesn´t look perfect but works. I printed the Adapterplate and the Suction-Duct as extra parts. To Avoid problems with supports i cut...
thingiverse
Customized version of https://www.thingiverse.com/thing:215386 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=215386
thingiverse
Should print with the flat sides down, requires no supports. The mount attachment should attach to the spool holder. The pieces are joined together with a #6 bolt, though the hole printed out at about 3.5mm in diameter. ... As the tolerances are...
thingiverse
This is a print to put the extruder on top off the original hotend. ...The piece is fastend with three m3 screws
thingiverse
I had a problem that after installing the backlight from: https://www.thingiverse.com/thing:2797456 I didn't know how to carefully insert the button, and at night I was annoyed by the extra light from the printer, so I quickly drew and glued...
thingiverse
This is a remix of spange's spool holder with wheels. ... the original project is here: https://www.thingiverse.com/thing:5078643 I enlarged outer rims because the filament reel had the tendency to fall off the holder.
thingiverse
You can use it for other printer or stuff, if it have 52mm wide. ...Also the Lamp has a diameter of 30mm.
thingiverse
The Anycubic Photon FEP Replacement Calibration Cap Measures a Compact 48mm x 27mm x 9mm.
cults3d
Underframe for Anycubic I3 Mega/Mega s, 120mm fan and sd slot installed
thingiverse
Unterbau Rahmen für Anycubic I3 Mega/Mega s, 120mm lüfter und sd slot verlegt
thingiverse
Securely fasten the extruder assembly to the stationary baseplate using the designated attachment points, ensuring a sturdy connection that withstands printing operations.