anycubic mega zero 2 3d models

Anycubic Mega Zero 12mm Probe mount, mounts to endstop. 12V20A Power supply mount - https://www.thingiverse.com/thing:4741667 Mosfet heated bed strain relief (frame mount) - https://www.thingiverse.com/thing:4761132 https://paypal.me/Ski3D Print...

This is an X-Gantry Cable Guide for the Anycubic Mega Zero to keep the cable bundle away from the stepper motor and lead screw. ...It's shorter than similar designs for the Ender 3 and does not need to be mirrored when printing. I printed it in ABS+ as...

This is the custom fan mount I've crafted to accommodate a 50mm centrifugal fan on my Mega Zero. ...Check out the original fan duct design on Thingiverse.

This mod will give your old Mega Zero (v1) printer a new life. This will convert one into a Pen Plotter. I removed the hot-end, fan, and other things that generated heat and turned off those settings in cura. I screwed in the mount where the extruder...

Credit for this inspiration goes to Derokero, https://www.thingiverse.com/thing:4111545 This is implemented on an AnyCubic Mega Zero printer using the supplied 2.4mm Allen-key on a SKR 1.4 Turbo board. Microswitch is wired to the servo probe port. ...

... height for a stock nozzle. I can't verify because I have a MicroSwiss nozzle. I am working on correcting this based on the feedback of users. See progress here https://www.thingiverse.com/groups/anycubic-mega-zero/forums/general/topic:48500**

Unfortunately, no fan duct updates is available for Anycubic Mega Zero across Internet, so, I had to design my own. I concatenated well known Ender 3 fan duct upgrade and fabric fan duct (many thanks to Anycubic, which provides stl file of this...

This is my dimensionally accurate, (after many iterations & fails), of the left rear mount required when upgrading to a dual Z axis configuration. I have also included the stepper bracket as mine was modelled using a thinner than the standard OE...

handy for manually leveling the bed **END EDIT** This is part of my attempt to remove the use of v-wheels from the Anycubic Mega Zero. For this mod you will need the following parts: **Needed Parts** - (1) 350mm MGN9H - 300mm should work as well...

Bottom part is used as-is, stock metal cover & fan. To fix smoothers I used model https://www.thingiverse.com/thing:3351822 Print Settings Printer: Anycubic Mega Zero Rafts: No</div>Supports: No Resolution: 0.28</div>Infill: 20%...

I don't have the dimensions for the Anycubic Mega Zero V2 but as long as the gap between the z-plates are 27mm then this will work. **Testing comments**: I've also made a mod that uses linear rods for the Z-axis...

https://youtu.be/bGszZp_2sEU This is part of a series of mod designs for the Mega Zero V1, here are others mods I've designed: - [MGN9 X-Axis](https://www.thingiverse.com/thing:4830265) - [MGN12 Y-Axis](https://www.thingiverse.com/thing:4903945) -...

I haven't got success with available fan duct for Mega Zero, so I decided to develop new one. And here it is. It works with 4020 fan. I selected it since it was most productive from a bunch available in my table :). Test results - it works...

Even though there seem a lot of these second Z mounts out there, they are mostly, (99.9%), designed around the Creality printers, which have different screw spacings to the Mega Zero & will cause binding, I know, I've been there done that. ... ...

... to support BTT SKR mini E3 v1-3. ...Space for a Pi Zero 2w have not tested pi zero but it should fit. ...Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder Category: 3D Printer Parts

New mainboard casing to support BTT SKR mini E3 v1-3. ... Space for a Pi Zero 2w have not tested pi zero but it should fit. ... Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder

... were solved and the filament reels would rotate more smoothly and they wouldn't come off. following parts are required. bearings 608zz x 2 M3 x 15 ~ 20mm screws x 2 The corresponding reel holes are 40mm or more and the width is 70mm or less.

Fixed version of fan holder. ... Original version is splitted to two parts (the mount is separated from the base) You will to have 2 screws M2x14 and one M2x18 for install. ... upd: added second version

... mount. ... Mounts over X_MIN limit switch using existing X_MIN limit switch screws. Nozzle to Probe Offset values as follows: NOZZLE_TO_PROBE_OFFSET{-37, -13, -2.195} Please note that the Z will vary depending on your hot-end assembly. ...

House number 2 in my series of houses for N Scale. ... This one has a little more detail in the siding. This is a 1960 style house from the design of the windows and ranch style. Printed with my Anycubic mega zero 2 with no supports perfectly. ...

... a layer of clear color finish to get it waterproof.Also used a bit of clear silicone here and there. Used an old wristwatch glass for Lens cover. ------------------------------------------------------ Printer: Anycubic Mega Zero 2.0 Resolution: 0.2

This is the base code for anycubic's mega zero 3d printer model, specifically version 0.0.4. ... Marlin 2.0 Firmware Version To view the correct display language on your lcd screen, you will need to change the configuration in the configuration.h file...

Enjoy making your own creations and sharing them with others!

Enjoy and share your make

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

A tiny spiral air vent is needed to fit a 50 by 15 fan on an AnyCubic Mega Zero.

**Note that this design is for the MegaZero 1.0** This was requested in the Anycubic Mega Zero group: https://www.thingiverse.com/groups/anycubic-mega-zero/forums/general/topic:49217#comment-5194831 **If you have any ideas for other parts, please...

------------------------------------------------------------------------------------------------------------------------ **Updates** Update 13-10-2021 - rev.0 published...

**Repository of the files created.** **See Anycubic Mega Zero group: https://www.thingiverse.com/groups/anycubic-mega-zero/forums/general/topic:49421** (1A is for the stock hotend) (1B is for the E3D v6 hotend) **Final parts are posted here:...

I remix this mount for use with my hotbed upgrade of Anycubic Mega Zero, based on AdaptedMachining project: https://www.thingiverse.com/thing:4295816 I did a little changes for power connectors: big one is input connector with power switch and second...