anycubic mega zero extruder 3d models
108251 3d models found related to anycubic mega zero extruder.thingiverse
Got tired of the print bed pulling the extruder cables so I designed this little clip to address that problem. ...
thingiverse
Note 2* anycubic mega zero V1 is 12V and V2 is 24V)) stock extruder with the stock stepper motor 2 blower fan 5015 (Note* anycubic mega zero V1 is 12V and V2 is 24V) https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the...
thingiverse
fan duct for Calvin_MegaZero's Direct drive mount basis: https://www.thingiverse.com/thing:4841439
thingiverse
Frankensteiner hood is a very nice product. I like it so much that I modified it to carry the Sherpa mini. And because the Sherpa monn motor has heat, the fan is enlarged to 60mm and the inside is split so that the wind cools the motor. ...
thingiverse
This is just a simple knob. ...Fit was tested on an [Anycubic Mega Zero](https://www.digitec.ch/de/s1/product/anycubic-mega-zero-3d-drucker-13573014).
thingiverse
e3d v6 mount for the Anycubic Mega Zero. Almost no supports required. ... Designed for a 50mm radial fan
thingiverse
Ein Extruderadapter für den Mega X und I3 Mega für den Titan. ... Sorgt für bessere Bedienbarkeit.
thingiverse
This is a scraper holder for the included scraper that comes with the Anycubic Mega Zero 3D printer. ...It slips into the side of the printer (you need to take one of the tiles off of the side) and allows you to easily store your scraper in a reachable...
thingiverse
... my custom designed spatula and cutter holder. ... It is fixed by sliding it in 20x20mm profiles so it can be installed in all printers that have this type of structure. I designed to use with my Anycubic Mega Zero for sliding in the left base profile.
thingiverse
I wanted to use teaching techs webcam mount for octoprint so i made a base for the front left of the frame for the Mega Zero 1 and 2 note: I have included standard files that are universal but if you want a specific camera mount you will have to find...
thingiverse
A containter for tools for Mega Zero or eny other printer with 20mm alluminium profiles
thingiverse
Hi, So I put a new roll of filament on my Anycubic Mega Zero and it is so tightly wound that the filament would pull back and sometimes the roll would jump/ skip after the extruder pulled hard enough on the filament. I decided to make a quick...
thingiverse
Remix to fit the Anycubic Mega Zero 1.0 & 2.0. Added a slot for the wires of the front fan and a rib to hold/ move the wires of the hotend away from the heatsink. Adjusted the front fan air tunnel so that it is more directed towards the heatsink....
myminifactory
This caddy is designed for use with the track frame of the Anycubic Mega Zero printer and, more specifically, on the base (for the horizontal mount) or exterior sides (for the vertical mount). This is NOT suitable for the top bar of the frame. The...
thingiverse
This fan mount replaces the stock fan cover and parts fan blower for the Anycubic Mega Zero. Other than the screw to hold the blower fan up top, it uses the same couple pieces of hardware as the original, and uses the original fans if you use a...
thingiverse
This is a remix of https://www.thingiverse.com/thing:4740153 for the Mega Zero v1/v2. It uses a tire gauge to help with manual bed leveling. This mounts to the x-limit switch slot. You'll need to remove the limit switch before mounting. BOM: ...
thingiverse
I have the Anycubic Mega S, but had the extruder filament release handle break on me, so I ended up replacing the whole extruder assembly from an old I3 mega, which is much better and made out of aluminum instead of plastic. I had to tinker with the...
thingiverse
Made this simple adpater for my Anycubic Mega-S printer. The extruder is 2,5cm displaced to the left to fit to the filament sensor. So the filment goes to the side and not straight. ... This adapter fixes ths issue.
cults3d
Dual Extruder Mount for the Anycubic Mega/Mega S (and probably compatible with a lot of different printers ) It is also possible to use it as a way to mount a bmg on the Mega without using it upside down or buying a mirrored one. ...for dual printing it...
thingiverse
Extruder Knob for Anycubic i3 Mega Printed with PLA, no support, 10% infill. I have realesed more tight version as well in case that it will not fit perfectly(not tested). But original version should be fine, working for me. All files included. ... ...
cults3d
Extruder Knob for Anycubic i3 Mega Printed with PLA, no support, 10% infill. I have realesed more tight version as well in case that it will not fit perfectly(not tested). But original version should be fine, working for me. All files included. ... It...