anycubic mega zero firmware update 3d models

This is an X-Gantry Cable Guide for the Anycubic Mega Zero to keep the cable bundle away from the stepper motor and lead screw. ...It's shorter than similar designs for the Ender 3 and does not need to be mirrored when printing. I printed it in ABS+ as...

This is the custom fan mount I've crafted to accommodate a 50mm centrifugal fan on my Mega Zero. ...Check out the original fan duct design on Thingiverse.

Available in Right and Left Side versions. The main enhancements are: 1/ Added extra reinforcing to improve rigidity 2/ Reinforced gantry mounting holes 3/ Made it adjustable so you can ensure your lead screw is parallel with the gantry I recommend...

I got inspiration from: https://www.thingiverse.com/thing:3796938 and thought that this was a extremely clean and simple answer to adding a second Z stepper & leadscrew to my Anycubic Mega Zero 2. Having tried many other designs to attempt this...

I got inspiration from: https://www.thingiverse.com/thing:3796938 and thought that this was a extremely clean and simple answer to adding a second Z stepper & leadscrew to my Anycubic Mega Zero 2. Having tried many other designs to attempt this...

Hi, I modified the board for the Anicubic Mega Zero 2, I used a cheap 2004A display, an encoder, and a beeper, there are also two reset wires. ...I'll post a video review later.

handy for manually leveling the bed **END EDIT** This is part of my attempt to remove the use of v-wheels from the Anycubic Mega Zero. For this mod you will need the following parts: **Needed Parts** - (1) 350mm MGN9H - 300mm should work as well...

Anycubic Mega Zero 12mm Probe mount, mounts to endstop. 12V20A Power supply mount - https://www.thingiverse.com/thing:4741667 Mosfet heated bed strain relief (frame mount) - https://www.thingiverse.com/thing:4761132 https://paypal.me/Ski3D Print...

This is my dimensionally accurate, (after many iterations & fails), of the left rear mount required when upgrading to a dual Z axis configuration. I have also included the stepper bracket as mine was modelled using a thinner than the standard OE...

... stock M5 Nylock Nuts. Print this at 50% & Cubic infill with 6 Top / Bottom Layers / Wall Lines for maximum strength. You can find my full Dual Z-Screw Guide for the Anycubic Mega Zero Printers here: https://www.thingiverse.com/thing:4810046

Bottom part is used as-is, stock metal cover & fan. To fix smoothers I used model https://www.thingiverse.com/thing:3351822 Print Settings Printer: Anycubic Mega Zero Rafts: No</div>Supports: No Resolution: 0.28</div>Infill: 20%...

This mod will give your old Mega Zero (v1) printer a new life. This will convert one into a Pen Plotter. I removed the hot-end, fan, and other things that generated heat and turned off those settings in cura. I screwed in the mount where the extruder...

Credit for this inspiration goes to Derokero, https://www.thingiverse.com/thing:4111545 This is implemented on an AnyCubic Mega Zero printer using the supplied 2.4mm Allen-key on a SKR 1.4 Turbo board. Microswitch is wired to the servo probe port. ...

I haven't got success with available fan duct for Mega Zero, so I decided to develop new one. And here it is. It works with 4020 fan. I selected it since it was most productive from a bunch available in my table :). Test results - it works...

Even though there seem a lot of these second Z mounts out there, they are mostly, (99.9%), designed around the Creality printers, which have different screw spacings to the Mega Zero & will cause binding, I know, I've been there done that. ... ...

I don't have the dimensions for the Anycubic Mega Zero V2 but as long as the gap between the z-plates are 27mm then this will work. **Testing comments**: I've also made a mod that uses linear rods for the Z-axis...

https://youtu.be/bGszZp_2sEU This is part of a series of mod designs for the Mega Zero V1, here are others mods I've designed: - [MGN9 X-Axis](https://www.thingiverse.com/thing:4830265) - [MGN12 Y-Axis](https://www.thingiverse.com/thing:4903945) -...

New mainboard casing to support BTT SKR mini E3 v1-3. ... Space for a Pi Zero 2w have not tested pi zero but it should fit. ... Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder

... to support BTT SKR mini E3 v1-3. ...Space for a Pi Zero 2w have not tested pi zero but it should fit. ...Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder Category: 3D Printer Parts

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

While replacing all the fans in my Anycubic 3d printer to make it quieter I replaced the stock 60x15mm cooling fan of the PSU with a silent 60x25mm fan. Because the replacement fan was thicker I had to mount it on the outside of the PSU, thus...

Anycubic i3 Mega / Mega-S Marlin 1.1.9 by davidramiro Donate to support this project: [](https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=6B6SAL5XRH842&source=url)...

Firmware Marlin 2.0.9.2 for Anycubic I3 Mega stock and installed TMC2225+DRV8825+BMG. MBL works properly. Sorces are for TMC2225+DRV8825+BMG. ... Installation via Cura Printer setup-update firmware-my file: AI3M2092-TMC2225-DRV8825-BMG-MBL.hex

This firmware can be found below if someone wants to use it as a starting point for their build: https://github.com/ssevillano/Anycubic-Mega-Zero-SKR-Mini-V2.0 The stock power brick does not have the amps required to power a heated bed and used a...

Powersupply Mount for Anycubic Mega Zero 2.0 and Mean Well LRS-350-24

12.09.21 I re-uploaded the marlin firmware with the both Z stepper motors and endstops working. I just need to figure out how to get the SD card reader working again. As far as the lcd screen goes, it was able to rotate in a previous version of...

12.09.21 I re-uploaded the marlin firmware with the both Z stepper motors and endstops working. I just need to figure out how to get the SD card reader working again. As far as the lcd screen goes, it was able to rotate in a previous version of...

Enjoy making your own creations and sharing them with others!

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...