anycubic mega zero firmware 3d models

Unfortunately, no fan duct updates is available for Anycubic Mega Zero across Internet, so, I had to design my own. I concatenated well known Ender 3 fan duct upgrade and fabric fan duct (many thanks to Anycubic, which provides stl file of this...

... stock M5 Nylock Nuts. Print this at 50% & Cubic infill with 6 Top / Bottom Layers / Wall Lines for maximum strength. You can find my full Dual Z-Screw Guide for the Anycubic Mega Zero Printers here: https://www.thingiverse.com/thing:4810046

Anycubic Mega Zero 12mm Probe mount, mounts to endstop. 12V20A Power supply mount - https://www.thingiverse.com/thing:4741667 Mosfet heated bed strain relief (frame mount) - https://www.thingiverse.com/thing:4761132 https://paypal.me/Ski3D Print...

Remix of https://www.thingiverse.com/thing:3052488 to fit the Anycubic Mega Zero 1.0. REV04a: Increased bearing height with 3mm and made the bottom thinner so that filament is in line with the extruder. In REV04b and 04c, the height is...

This is my dimensionally accurate, (after many iterations & fails), of the left rear mount required when upgrading to a dual Z axis configuration. I have also included the stepper bracket as mine was modelled using a thinner than the standard OE...

Bottom part is used as-is, stock metal cover & fan. To fix smoothers I used model https://www.thingiverse.com/thing:3351822 Print Settings Printer: Anycubic Mega Zero Rafts: No</div>Supports: No Resolution: 0.28</div>Infill: 20%...

This mod will give your old Mega Zero (v1) printer a new life. This will convert one into a Pen Plotter. I removed the hot-end, fan, and other things that generated heat and turned off those settings in cura. I screwed in the mount where the extruder...

Credit for this inspiration goes to Derokero, https://www.thingiverse.com/thing:4111545 This is implemented on an AnyCubic Mega Zero printer using the supplied 2.4mm Allen-key on a SKR 1.4 Turbo board. Microswitch is wired to the servo probe port. ...

I haven't got success with available fan duct for Mega Zero, so I decided to develop new one. And here it is. It works with 4020 fan. I selected it since it was most productive from a bunch available in my table :). Test results - it works...

handy for manually leveling the bed **END EDIT** This is part of my attempt to remove the use of v-wheels from the Anycubic Mega Zero. For this mod you will need the following parts: **Needed Parts** - (1) 350mm MGN9H - 300mm should work as well...

Even though there seem a lot of these second Z mounts out there, they are mostly, (99.9%), designed around the Creality printers, which have different screw spacings to the Mega Zero & will cause binding, I know, I've been there done that. ... ...

I don't have the dimensions for the Anycubic Mega Zero V2 but as long as the gap between the z-plates are 27mm then this will work. **Testing comments**: I've also made a mod that uses linear rods for the Z-axis...

https://youtu.be/bGszZp_2sEU This is part of a series of mod designs for the Mega Zero V1, here are others mods I've designed: - [MGN9 X-Axis](https://www.thingiverse.com/thing:4830265) - [MGN12 Y-Axis](https://www.thingiverse.com/thing:4903945) -...

... to support BTT SKR mini E3 v1-3. ...Space for a Pi Zero 2w have not tested pi zero but it should fit. ...Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder Category: 3D Printer Parts

New mainboard casing to support BTT SKR mini E3 v1-3. ... Space for a Pi Zero 2w have not tested pi zero but it should fit. ... Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

While replacing all the fans in my Anycubic 3d printer to make it quieter I replaced the stock 60x15mm cooling fan of the PSU with a silent 60x25mm fan. Because the replacement fan was thicker I had to mount it on the outside of the PSU, thus...

Anycubic i3 Mega / Mega-S Marlin 1.1.9 by davidramiro Donate to support this project: [](https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=6B6SAL5XRH842&source=url)...

Firmware Marlin 2.0.9.2 for Anycubic I3 Mega stock and installed TMC2225+DRV8825+BMG. MBL works properly. Sorces are for TMC2225+DRV8825+BMG. ... Installation via Cura Printer setup-update firmware-my file: AI3M2092-TMC2225-DRV8825-BMG-MBL.hex

Powersupply Mount for Anycubic Mega Zero 2.0 and Mean Well LRS-350-24

This firmware can be found below if someone wants to use it as a starting point for their build: https://github.com/ssevillano/Anycubic-Mega-Zero-SKR-Mini-V2.0 The stock power brick does not have the amps required to power a heated bed and used a...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Enjoy making your own creations and sharing them with others!

Enjoy and share your make

A tiny spiral air vent is needed to fit a 50 by 15 fan on an AnyCubic Mega Zero.

12.09.21 I re-uploaded the marlin firmware with the both Z stepper motors and endstops working. I just need to figure out how to get the SD card reader working again. As far as the lcd screen goes, it was able to rotate in a previous version of...

12.09.21 I re-uploaded the marlin firmware with the both Z stepper motors and endstops working. I just need to figure out how to get the SD card reader working again. As far as the lcd screen goes, it was able to rotate in a previous version of...

This is Marlin 2.1.*-bugfix firmware for AnyCubic i3 Mega/Mega S with ТМС2208/2225+DRV8825E0+BMG+Mesh Bed Leveling Git repository: https://github.com/Digifan/Ai3M-TMC-BMG_Marlin-2.1.-bugfix/tree/bugfix-2.1.x

A recreation of the bottom part of the electronics enclosure of Anycubic Mega Zero 2.0 printer. ...Might be useful when designing your own enclosure.